Libec Electric pedestal with Floor Spreader for PTZ cameras

Libec Electric pedestal with Floor Spreader for PTZ cameras(LX-ePed2) Raise and lower your mounted camera of choice with this LX-ePed 2 Electric Pedestal Column with Ground Spreader from Libec thanks to its handheld controller and working height range of 37.5 to 97.2". Mount a camcorder, PTZ, or other recording device on the tripod using the 1/4"-20 and 3/8"-16 screws on its 100mm ball head and 22 lb load capacity. LAN ports on both the pedestal column and controller unit allow the devices to communicate using the included LAN cable. The cable features a length of 98.4', allowing you to operate at a distance. The elevation rocker on the controller allows for the intuitive raising and lowering of the tripod's center column up to 15.7". Continuous operation can be performed for three minutes at a time. An optional MPC-1 multi-protocol converter makes the system compatible with PTZ controllers and PC applications for precise adjustment. The included ground spreader provides additional security to the system, and an AC/DC power adapter provides power.

Libec HS-450MQ Tripod System with Mid-Level Spreader

Libec HS-450MQ Tripod System with Mid-Level Spreader(HS-450MQ) This HS-450MQ Tripod System from Libec features 2-stage legs with an 88.1 lb load capacity, a 75mm fluid head, a compatible mid-level spreader, three rubber feet, and a carrying case to bring it to the set. Intuitive adjustment of pan, tilt, and counterbalance makes for a customizable experience. Aluminum construction creates a lightweight and durable tripod design. Libec H45 75mm Ball and Flat Base Video Head with Pan Handle (26.5 lb Payload) Integrate a fluid head into your tripod configuration with various adjustment features using this H45 75mm Ball and Flat Base Video Head with Pan Handle from Libec. An included pan handle makes for easy movement up and down or side to side. Independent pan and tilt adjustments make movements intuitive and smooth. The H45 head has a load capacity of 26.5 lb and an adjustable counterbalance range of 9.9 to 23.1 lb. Your camera is secured via a 1/4"-20 screw and locating pin, and additional 3/8"-16 and 1/4"-20 screws are included for further attachments. The head also comes with a long sliding plate with one 3/8"-16 screw and one 1/4"-20 screw. An illuminated bubble level ensures your configuration is level when mounted onto tripod legs. The H45 is compatible with Manfrotto or Sachtler heads. Libec QL40B 2-Stage Lightweight Aluminum Tripod with 75mm Bowl The QL40B 2-Stage Lightweight Aluminum Tripod with 75mm Bowl from Libec is a durable tripod capable of accommodating larger cine rigs thanks to its 88.1 lb load capacity. A 75mm bowl head allows you to integrate a wide variety of fluid heads into your tripod configuration. A 21.6 to 71.6" working height range of the 2-stage legs can be adjusted using the flip-style quick locks. Three 1/4"-20 and 3/8"-16 threads on the legs allow you to integrate additional accessories. Libec BR-2B Mid-Level Spreader for RT20C and RT30B Tripods   The BR-2B Mid-Level Spreader from Libec is designed to offer added stability to RT20C and RT30B tripods. It installs onto the mid-level leg stage and can adjust the length of each arm by sliding them out and tightening them with locking knobs. Best used on uneven surfaces where ground spreaders won't lie flat, the BR-2B also keeps the tripod's legs from twisting.

Libec HS-350MQ Tripod System with mid-level spreader

Libec HS-350MQ Tripod System with mid-level spreader(HS-350MQ) This HS-350MQ Tripod System from Libec features 2-stage legs with an 88.1 lb load capacity, a 75mm fluid head, a compatible mid-level spreader, three rubber feet, and a carrying case to bring it to the set. Intuitive adjustment of pan, tilt, and counterbalance makes for a customizable experience. Aluminum construction creates a lightweight and durable tripod design. Libec H35 75mm Ball and Flat Base Video Head with Pan Handle (17.6 lb Payload) Integrate a fluid head into your tripod configuration with various adjustment features using this H35 75mm Ball and Flat Base Video Head with Pan Handle from Libec. An included pan handle makes for easy movement up and down or side to side. Independent pan and tilt adjustments make movements intuitive and smooth. The H35 head has a load capacity of 17.6 lb and an adjustable counterbalance range of 6.6 to 16.5 lb. Your camera is secured via a 1/4"-20 screw and locating pin, and additional 3/8"-16 and 1/4"-20 screws are included for further attachments. The head also comes with a long sliding plate with one 3/8"-16 screw and one 1/4"-20 screw. An illuminated bubble level ensures your configuration is level when mounted onto tripod legs. The H35 is compatible with Manfrotto or Sachtler heads. Libec QL40B 2-Stage Lightweight Aluminum Tripod with 75mm Bowl The QL40B 2-Stage Lightweight Aluminum Tripod with 75mm Bowl from Libec is a durable tripod capable of accommodating larger cine rigs thanks to its 88.1 lb load capacity. A 75mm bowl head allows you to integrate a wide variety of fluid heads into your tripod configuration. A 21.6 to 71.6" working height range of the 2-stage legs can be adjusted using the flip-style quick locks. Three 1/4"-20 and 3/8"-16 threads on the legs allow you to integrate additional accessories. Libec BR-2B Mid-Level Spreader for RT20C and RT30B Tripods The BR-2B Mid-Level Spreader from Libec is designed to offer added stability to RT20C and RT30B tripods. It installs onto the mid-level leg stage and can adjust the length of each arm by sliding them out and tightening them with locking knobs. Best used on uneven surfaces where ground spreaders won't lie flat, the BR-2B also keeps the tripod's legs from twisting. Compatibility Libec RT20C and RT30B tripods Libec Lightweight Rubber Foot for RT20C Tripod (Set of 3) These Lightweight Rubber Feet for RT20C Tripod from Libec provide improved traction on polished floors and other slick surfaces when using the RT20C carbon fiber tripod. They attach and remove quickly and prevent marring surfaces. Libec RC-40 Carrying Case The Libec RC-40 Carrying Case (Black) is a non-padded, vinyl case designed to carry a Libec RT-40 tripod with an RH-40 tripod head attached. It is carried by a handle or a removable, adjustable shoulder strap.    

Libec Tripod System with Mid-Level Spreader

Libec Tripod System with Mid-Level Spreader(HS-250MQ) This HS-250MQ Tripod System from Libec features 2-stage legs with an 88.1 lb load capacity, a 75mm fluid head, a compatible mid-level spreader, three rubber feet, and a carrying case to bring it to the set. Intuitive adjustment of pan, tilt, and counterbalance makes for a customizable experience. Aluminum construction creates a lightweight and durable tripod design. Libec H25 75mm Ball and Flat Base Video Head with Pan Handle (11 lb Payload) Integrate a fluid head into your tripod configuration with various adjustment features using this H25 75mm Ball and Flat Base Video Head with Pan Handle from Libec. An included pan handle makes for easy movement up and down or side to side. Independent pan and tilt adjustments make movements intuitive and smooth. The H25 head has a load capacity of 11 lb and an adjustable counterbalance range of 3.7 to 9.9 lb. Your camera is secured via a 1/4"-20 screw and locating pin, and additional 3/8"-16 and 1/4"-20 screws are included for further attachments. An illuminated bubble level ensures your configuration is level when mounted onto tripod legs. The H25 is compatible with Manfrotto or Sachtler heads. Libec QL40B 2-Stage Lightweight Aluminum Tripod with 75mm Bowl The QL40B 2-Stage Lightweight Aluminum Tripod with 75mm Bowl from Libec is a durable tripod capable of accommodating larger cine rigs thanks to its 88.1 lb load capacity. A 75mm bowl head allows you to integrate a wide variety of fluid heads into your tripod configuration. A 21.6 to 71.6" working height range of the 2-stage legs can be adjusted using the flip-style quick locks. Three 1/4"-20 and 3/8"-16 threads on the legs allow you to integrate additional accessories. Libec BR-2B Mid-Level Spreader for RT20C and RT30B Tripods The BR-2B Mid-Level Spreader from Libec is designed to offer added stability to RT20C and RT30B tripods. It installs onto the mid-level leg stage and can adjust the length of each arm by sliding them out and tightening them with locking knobs. Best used on uneven surfaces where ground spreaders won't lie flat, the BR-2B also keeps the tripod's legs from twisting. Compatibility Libec RT20C and RT30B tripods Libec Lightweight Rubber Foot for RT20C Tripod (Set of 3) These Lightweight Rubber Feet for RT20C Tripod from Libec provide improved traction on polished floors and other slick surfaces when using the RT20C carbon fiber tripod. They attach and remove quickly and prevent marring surfaces. Libec RC-40 Carrying Case   The Libec RC-40 Carrying Case (Black) is a non-padded, vinyl case designed to carry a Libec RT-40 tripod with an RH-40 tripod head attached. It is carried by a handle or a removable, adjustable shoulder strap.

Libec HS-150MQ Tripod System w/ mid-level spreader

Libec HS-150MQ Tripod System w/ mid-level spreader(HS-150MQ) This HS-150MQ Tripod System from Libec features 2-stage legs with an 88.1 lb load capacity, a 75mm fluid head, a compatible mid-level spreader, three rubber feet, and a carrying case to bring it to the set. Intuitive adjustment of pan, tilt, and counterbalance makes for a customizable experience. Aluminum construction creates a lightweight and durable tripod design. Libec H15 75mm Ball and Flat Base Video Head with Pan Handle (6.6 lb Payload) Integrate a fluid head into your tripod configuration with various adjustment features using this H15 75mm Ball and Flat Base Video Head with Pan Handle from Libec. An included pan handle makes for easy movement up and down or side to side. Independent pan and tilt adjustments make movements intuitive and smooth. The H15 head has a load capacity of 6.6 lb and an adjustable counterbalance range of 1.7 to 4.4 lb. Your camera is secured via a 1/4"-20 screw and locating pin, and additional 3/8"-16 and 1/4"-20 screws are included for further attachments. An illuminated bubble level ensures your configuration is level when mounted onto tripod legs. The H15 is compatible with Manfrotto or Sachtler heads. Libec QL40B 2-Stage Lightweight Aluminum Tripod with 75mm Bowl The QL40B 2-Stage Lightweight Aluminum Tripod with 75mm Bowl from Libec is a durable tripod capable of accommodating larger cine rigs thanks to its 88.1 lb load capacity. A 75mm bowl head allows you to integrate a wide variety of fluid heads into your tripod configuration. A 21.6 to 71.6" working height range of the 2-stage legs can be adjusted using the flip-style quick locks. Three 1/4"-20 and 3/8"-16 threads on the legs allow you to integrate additional accessories. Libec BR-2B Mid-Level Spreader for RT20C and RT30B Tripods The BR-2B Mid-Level Spreader from Libec is designed to offer added stability to RT20C and RT30B tripods. It installs onto the mid-level leg stage and can adjust the length of each arm by sliding them out and tightening them with locking knobs. Best used on uneven surfaces where ground spreaders won't lie flat, the BR-2B also keeps the tripod's legs from twisting. Compatibility Libec RT20C and RT30B tripods Libec Lightweight Rubber Foot for RT20C Tripod (Set of 3) These Lightweight Rubber Feet for RT20C Tripod from Libec provide improved traction on polished floors and other slick surfaces when using the RT20C carbon fiber tripod. They attach and remove quickly and prevent marring surfaces. Libec RC-40 Carrying Case   The Libec RC-40 Carrying Case (Black) is a non-padded, vinyl case designed to carry a Libec RT-40 tripod with an RH-40 tripod head attached. It is carried by a handle or a removable, adjustable shoulder strap.

Libec NX-300MQ Tripod System w/ Mid-Level Spreader

Libec NX-300MQ Tripod System w/ Mid-Level Spreader(NX-300MQ) This NX-300Q Tripod System from Libec features 2-stage legs with an 88.1 lb load capacity, a 75mm fluid head, a compatible ground spreader, and a carrying case to bring it to the set. Intuitive adjustment of pan, tilt, and counterbalance makes for a customizable experience. Aluminum construction creates a lightweight and durable tripod design. Libec NH30 75mm Ball/Flat Base Video Head with Pan Handle (22 lb Payload) Designed to support small camera rigs weighing up to 22 lb, the NH30 75mm Ball/Flat Base Video Head with Pan Handle from Libec features a unified ball/flat mount design. The base of the tripod can fit either in a standard 75mm bowl or on a flat mount with a 3/8"-16 screw. Having both options available means you can transfer the head from a tripod with a bowl mount to a flat mount slider.   To achieve proper balance, the NH30 head includes a snap-on/off camera plate that can slide up to 1.2" of fore/aft adjustment, and it features 1/4"-20 and 3/8"-16 camera mounting screw options. The screw and locating pin are moveable to orient the plate on the camera to achieve the best possible balance. Once the camera is balanced, the continuous counterbalance and pan/tilt drag controls provide smooth movement. On the side, there are 1/4"-20 and 3/8"-16 threads to mount a variety of accessories such as a light, monitor, or extension arm. Included with the NH30 is a pan handle that can be placed on the right or left side of the head by screwing it onto one of the mounts. The LED-illuminated bubble level helps to level the camera on uneven surfaces, even in low light. Libec QL40B 2-Stage Lightweight Aluminum Tripod with 75mm Bowl The QL40B 2-Stage Lightweight Aluminum Tripod with 75mm Bowl from Libec is a durable tripod capable of accommodating larger cine rigs thanks to its 88.1 lb load capacity. A 75mm bowl head allows you to integrate a wide variety of fluid heads into your tripod configuration. A 21.6 to 71.6" working height range of the 2-stage legs can be adjusted using the flip-style quick locks. Three 1/4"-20 and 3/8"-16 threads on the legs allow you to integrate additional accessories. Libec Long Sliding Plate S for TH-X, TH-Z, NH10 & NH30 Heads This Long Sliding Plate S from Libec helps to properly balance a heavier camera or camera rig with a longer lens on select tripod heads. This 9.4" long plate is constructed from an aluminum alloy and offers a 3.7" sliding range. It is compatible with Libec TH-X, TH-Z, NH10, and NH30 heads, as well as select Manfrotto and Sachtler heads.

Libec TH-M Kit Hands-Free Monopod Kit

Libec TH-M Kit Hands-Free Monopod Kit(TH-M-Kit, THM-Kit, TH M-Kit) The TH-M Hands-Free Monopod Kit from Libec is a hands-free monopod support system for recording with a video camera, camcorder, mirrorless, or DSLR camera. It features a 9 lb load capacity, a maximum working height of 74.6", and a minimum working height of 34.4". A Perfect Lock feature makes it easy to maneuver the monopod's head, and lock and release foot pedals let you quickly lock and release the unit during photo and video shoots. Designed to be a hands-free device, the monopod stands on its own with a wide range of cameras, allowing users to multi-task and make equipment adjustments in between shots, and the smooth movements of the head allow manual focus while simultaneously panning, tilting, and shooting. This kit's dual-head structure features a flat base and 65mm bowl, making the head compatible with 65mm bowls, flat base tripods, monopods, sliders, skater dollies, and other equipment with 3/8"-16 screws. The head features a one touch on/off sliding plate that is compatible with Manfrotto and Sachtler heads, and a dual-size, padded, travel bag is included so you can store and carry the monopod with or without the head. Hands-Free Monopod Fold-out feet increase stability and allow the monopod to stand on its own with a wide range of cameras, allowing you to multi-task and make equipment adjustments in between shots, without the need to lay the monopod on the ground or floor or lean it against a wall. Perfect Lock Feature Lock the bottom part of the monopod by stepping on the foot pedal, and the ball joint will be locked as well. This ensures the pan movement of the head on the monopod is smooth and allows you to control the camera's manual focus while panning and shooting. Upgraded Head Attachment The top cover of the TH-M monopod is equipped with both a 1/4"-20 and a 3/8"-16 screw hole. The 1/4"-20 screw is covered by a storable 3/8"-16 screw socket, allowing both kinds of equipment to be attached. Smooth Panoramic Rotation At the base of the unit a special built-in lubricated ball joint system, designed to prevent dust and debris from entering, offers smooth quality movements. Quick Adjustments for Your Preferred Height A sleek design with numeric indicators for preferred height settings improves the usability of the monopod when it's necessary to frequently adjust height settings. Speedy Open and Close Functions Designed for swift setups and compact travel, user-friendly folding legs can be easily opened and closed with a push of a button. Pan Tilt Head with Dual Head Structure The head has tilt and pan functions, and the unit's dual-head structure features a flat base and 65mm bowl, making the head compatible with 65mm bowls, flat base tripods, monopods, sliders, skater dollies, and other equipment with 3/8"-16 screws. Sliding Plates Compatible with Manfrotto and Sachtler Heads This one touch on/off sliding plate is compatible with Manfrotto and Sachtler heads, enabling quick equipment swaps without the need to change sliding plates. Dual size Carrying Bag   A dual size travel bag is included to carry and store the monopod with or without the head.

Libec Heavy Duty Tripod

Libec Heavy Duty Tripod(T150F) The Libec T150F consists of heavy-duty aluminum tripod legs with a 4-bolt flat base. It supports up to 220.5 lb and extends from 23 to 64" in two stages. The T150F's legs have a twist leg lock knob at each stage for a quick setup. This rugged aluminum construction is suited for heavy use with flat base heads.

Libec HS-450 Tripod System - FS

Libec HS-450 Tripod System - FS(HS-450 , HS 450 , HS450 ) Perfect Balance Libec's unique continuous perfect counterbalance system enables the camera to perfectly balance at any tilt angle. This smooth balance system makes it a lot easier for users to concentrate on precise camera movements, even when using a telephoto lens at its maximum zoomed position. Newly Designed Fluid Head From scratch, the fluid head was designed to dramatically reduce play inside its superior pan and tilt drag units, dramatically increasing its longevity. From start to finish, this new fluid head provides ultra-smooth movements and is equipped with many features that enhance a user's experience. Counterbalance Meter Equipped with a counterbalance meter with the measurement range of 0 to 100. This allows users to glance at the head's minimum/maximum inner spring strength, making camera balances on site a piece of cake. Snap On/Off Plate The slide plate can be attached and released with just one-touch. Quick and easy setups in the field are easily achieved. Advanced Drag Unit The layered metal unit in the drag system ensures operability, durability and reliability. Thanks to the finest silicon grease applied, the advanced drag unit offers smoother starts and ultimately improved backlash control. In addition, the grease provides ordinary pan and tilt movements at a wide temperature range from -40˚C/-40˚F up to +60˚C/+140˚F. The variable 4 step drag pan tilt system features a zero "free" mode option with no friction. Unlike other brand heads, there is no need to store it in its zero "free" mode. Dual Head The Dual-head base specification allows for a quick set-up with both 75mm bowl and flat base tripods. The Dual-head base is also compatible with sliders, skater dollies, and photo tripods. User Friendly Accessory Port Equipped on the fluid head's side, there are 1/4 and 3/8 inch screw holes allowing users to attach an accessory arm to hold monitors, lights and other accessories. Since the holes are located on the base, the payload capacity, center of gravity and front-rear balance of the head are not affected. LED Bubble Level   The bubble level is equipped with an LED light allowing users to level a tripod head in the dark. In addition, the counterbalance meter is also illuminated.

Libec 75mm ball and flat base video head H35

Libec 75mm ball and flat base video head  H35(H35) Perfect Balance Libec's unique continuous perfect counterbalance system enables the camera to perfectly balance at any tilt angle. This smooth balance system makes it a lot easier for users to concentrate on precise camera movements, even when using a telephoto lens at its maximum zoomed position. Newly Designed Fluid Head From scratch, the fluid head was designed to dramatically reduce play inside its superior pan and tilt drag units, dramatically increasing its longevity. From start to finish, this new fluid head provides ultra-smooth movements and is equipped with many features that enhance a user's experience. Counterbalance Meter Equipped with a counterbalance meter with the measurement range of 0 to 100. This allows users to glance at the head's minimum/maximum inner spring strength, making camera balances on site a piece of cake. Snap On/Off Plate The slide plate can be attached and released with just one-touch. Quick and easy setups in the field are easily achieved. Advanced Drag Unit The layered metal unit in the drag system ensures operability, durability and reliability. Thanks to the finest silicon grease applied, the advanced drag unit offers smoother starts and ultimately improved backlash control. In addition, the grease provides ordinary pan and tilt movements at a wide temperature range from -40˚C/-40˚F up to +60˚C/+140˚F. The variable 4 step drag pan tilt system features a zero "free" mode option with no friction. Unlike other brand heads, there is no need to store it in its zero "free" mode. Dual Head The Dual-head base specification allows for a quick set-up with both 75mm bowl and flat base tripods. The Dual-head base is also compatible with sliders, skater dollies, and photo tripods. User Friendly Accessory Port Equipped on the fluid head's side, there are 1/4 and 3/8 inch screw holes allowing users to attach an accessory arm to hold monitors, lights and other accessories. Since the holes are located on the base, the payload capacity, center of gravity and front-rear balance of the head are not affected. LED Bubble Level   The bubble level is equipped with an LED light allowing users to level a tripod head in the dark. In addition, the counterbalance meter is also illuminated.

Libec H15 75mm ball and flat base video head

Libec H15 75mm ball and flat base video head(H15) Integrate a fluid head into your tripod configuration with various adjustment features using this H15 75mm Ball and Flat Base Video Head with Pan Handle from Libec. An included pan handle makes for easy movement up and down or side to side. Independent pan and tilt adjustments make movements intuitive and smooth. The H15 head has a load capacity of 6.6 lb and an adjustable counterbalance range of 1.7 to 4.4 lb. Your camera is secured via a 1/4"-20 screw and locating pin, and additional 3/8"-16 and 1/4"-20 screws are included for further attachments. An illuminated bubble level ensures your configuration is level when mounted onto tripod legs. The H15 is compatible with Manfrotto or Sachtler heads.

Libec HS-150MC Tripod System with Mid-level Spreader

Libec HS-150MC (HS/150MC, HS_150MC, HS150MC, HS 150MC) HS-150MC Tripod System with Mid-level Spreader HS-150MC Tripod System from Libec features 2-stage legs with a 6.6 lb load capacity, a 75mm fluid head, a compatible mid-level spreader, three rubber feet, and a carrying case to bring it to set. Intuitive adjustment of pan, tilt, and counterbalance makes for a customizable experience. Aluminum construction creates a lightweight and durable tripod design. Perfect Counterbalance With Libec’s continuous counterbalance, the newly designed fluid head offers ultra-smooth movements. Allowing even lightweight cameras to balance. Counterbalance Meter This will allow users to quickly recalibrate for different cameras on the head. Advanced Drag System The metal drag system reduces backlash and allows operation in extreme temperatures --40˚C/-40˚F up to +60˚C/+140˚F. Accessory port, Dual head, Snap on release plate and LED bubble balance as standard.  

Libec HS-150C Tripod System with Floor Spreader

Libec HS-150C (HS/150C, HS_150C, HS150C, HS 150C) Tripod System with Floor Spreader HS-150C Tripod System from Libec supports a load up to 6.6 lb and features 2-stage aluminum legs, a durable 75mm fluid head, a sturdy ground spreader, and a carrying case to bring it to set. Intuitive adjustment of pan, tilt, and counterbalance makes for a customizable experience. Aluminum construction creates a lightweight and durable tripod design. Perfect Counterbalance With Libec’s continuous counterbalance, the newly designed fluid head offers ultra-smooth movements. Allowing even lightweight cameras to balance. Counterbalance Meter This will allow users to quickly recalibrate for different cameras on the head. Advanced Drag System The metal drag system reduces backlash and allows operation in extreme temperatures --40˚C/-40˚F up to +60˚C/+140˚F. Accessory port, Dual head, Snap on release plate and LED bubble balance as standard.

Libec RT20C 2 Stage Lightweight Carbon Tripod with 75mm Bowl

Libec RT20C (RT-20C, RT/20C, RT_20C, RT 20C, rt20c) 2 Stage Lightweight Carbon Tripod with 75mm Bowl Add a durable, lightweight tripod to your camera rig with this RT20C 2-Stage Lightweight Carbon Fiber Tripod with 75mm Bowl from Libec. The RT20C offers a 75mm bowl fitting for mounting a wide variety of fluid heads. Without the included feet and spreader, the lightweight carbon fiber legs weigh only 3.5 lb. Secured by twist levers, the 2-stage legs have a height range of 14.6 to 60.6".

Libec NX-300C Carbon Fiber Tripod System with Floor Spreader

Libec NX-300C (NX/300C, NX_300C, NX300C, NX 300C, nx-300c) Carbon Fiber Tripod System with Floor Spreader The NX-300C/MC models have an outstanding counterbalance range. These models cover a wide of camera configurations with payloads between 2.5kg and 10kg. The NX-300 Series is a must have tripod system that supports a wide range of rigged small cameras, mid-sized handheld cameras and rigged out professional cinema cameras. Operability with Precision Thanks to specially skilled craftsmen in Libec Japan, we adapted an innovative design to maximize NX's performance. As result, a significant reduction in wobbling and backlash in pan and tilt movements is achieved and offers the best precision operability in its range by far. Newly Designed Multistep Counterbalance Mechanism The NX series can support a wide range of camera configurations with a newly designed multistep counterbalance system that fits variety of production styles. Users can select from 5 steps of counterbalance including a zero "free" mode option for speedy set-up. Advanced Drag Unit The layered metal unit in the drag system ensures operability, durability and reliability. This advanced drag unit offers smoother starts, improved backlash control and more rigidity than a conventional low cost plastic unit commonly adapted by other brands. Highly Reliable Multistep Drag System The NX series features the variable 4 step drag pan tilt system that includes a zero "free" mode option with no friction. In addition, the finest silicon grease is applied to ensure ordinary pan and tilt movements at a wide temperature range from -40˚C/-40˚F up to +60˚C/+140˚F. Newly Designed Carbon Legs, Foot Pads and Spreader With a new lightweight structure design, the width of the carbon leg's upper pipe leg is widened to enhance torsional rigidity and provide high payload performance. Developed exclusively for the NX series, the FP-1B foot pads and SP-1B floor spreader are available. The newly designed foot pads and floor spreader are even lighter than the existing model FP-2B and SP-2B. User Friendly Accessory Attachments On the side of the fluid head, there are 1/4 and 3/8 inch screw holes to attach an accessory arm with a monitor or a light. Since the holes are located on the base, the payload capacity, center of gravity and front-rear balance are not affected. Double-sided Serrations Serrations are equipped on both sides of the head to accommodate an additional pan handle or other accessories. Dual Head Dual-head specification is available for both 75mm bowl and flat base tripods. The Dual-head is also compatible with sliders, skater dollies, and photo tripods. Snap ON/OFF Sliding Plate The sliding plate can be attached and released with just one-touch. Easy and smooth settings in the field are easily achieved. Highly Compatible Sliding Plate Compatible with the hands-free monopod "TH-M", the electric gimbal "TH-G3", and other brand camera accessories. The sliding plate allows users to quickly swap between a wide range of camera supports. LED Bubble Level The bubble level is equipped with an LED light to level a tripod in the dark. Safety Design With safety in mind, the tripod legs are carefully designed to prevent the tripod from collapsing on a user's fingers, even if the tripod is collapsed unintentionally. Multi-functional Carrying Case This special carrying case includes a shoulder strap, handles and a zipped pocket.

Libec NX-100MC Carbon Fiber Tripod System with Mid-Level Spreader

Libec NX-100MC (NX/100MC, NX_100MC, NX100MC, NX 100MC, nx-100mc) Carbon Fiber Tripod System with Mid-Level Spreader The NX-100C/MC models are specially designed for small cameras and its excellent counterbalance range system can even balance the lightest configuration of a mirrorless camera with a kit lens. In addition, the optimally adjusted drag system provides great operability and smooth start and stop of pan and tilt movements. The NX-100 Series is great for mirrorless cameras, DSLRs, small handheld cameras and light rigged cameras. The World's Lightest Video Tripod The NX-100MC/NX-300MC mid-level spreader systems only weigh 3.8 kg and are considered the world's lightest video tripods compared to conventional video tripods equipped with adjustable drag and counterbalance systems. This is achieved by closely exploring the structure, materials, and components, adapting a new mechanism that significantly reduces the number of parts, and applying plastic parts for the main component without compromising operability or functionality. Operability with Precision Thanks to specially skilled craftsmen in Libec Japan, we adapted an innovative design to maximize NX's performance. As result, a significant reduction in wobbling and backlash in pan and tilt movements is achieved and offers the best precision operability in its range by far. Newly Designed Multistep Counterbalance Mechanism The NX series can support a wide range of camera configurations with a newly designed multistep counterbalance system that fits variety of production styles. Users can select from 5 steps of counterbalance including a zero "free" mode option for speedy set-up. Advanced Drag Unit The layered metal unit in the drag system ensures operability, durability and reliability. This advanced drag unit offers smoother starts, improved backlash control and more rigidity than a conventional low cost plastic unit commonly adapted by other brands. Highly Reliable Multistep Drag System The NX series features the variable 4 step drag pan tilt system that includes a zero "free" mode option with no friction. In addition, the finest silicon grease is applied to ensure ordinary pan and tilt movements at a wide temperature range from -40˚C/-40˚F up to +60˚C/+140˚F. Newly Designed Carbon Legs, Foot Pads and Spreader With a new lightweight structure design, the width of the carbon leg's upper pipe leg is widened to enhance torsional rigidity and provide high payload performance. Developed exclusively for the NX series, the FP-1B foot pads and SP-1B floor spreader are available. The newly designed foot pads and floor spreader are even lighter than the existing model FP-2B and SP-2B. User Friendly Accessory Attachments On the side of the fluid head, there are 1/4 and 3/8 inch screw holes to attach an accessory arm with a monitor or a light. Since the holes are located on the base, the payload capacity, center of gravity and front-rear balance are not affected. Double-sided Serrations Serrations are equipped on both sides of the head to accommodate an additional pan handle or other accessories. Dual Head Dual-head specification is available for both 75mm bowl and flat base tripods. The Dual-head is also compatible with sliders, skater dollies, and photo tripods. Snap ON/OFF Sliding Plate The sliding plate can be attached and released with just one-touch. Easy and smooth settings in the field are easily achieved. Highly Compatible Sliding Plate Compatible with the hands-free monopod "TH-M", the electric gimbal "TH-G3", and other brand camera accessories. The sliding plate allows users to quickly swap between a wide range of camera supports. LED Bubble Level The bubble level is equipped with an LED light to level a tripod in the dark. Safety Design With safety in mind, the tripod legs are carefully designed to prevent the tripod from collapsing on a user's fingers, even if the tripod is collapsed unintentionally. Multi-functional Carrying Case This special carrying case includes a shoulder strap, handles and a zipped pocket.

Libec NX-100C Carbon Fiber Tripod System with Floor Spreader

Libec NX-100C (NX/100C, NX_100C, NX 100C, NX100C, nx-100c) Carbon Fiber Tripod System with Floor Spreader The NX-100C/MC models are specially designed for small cameras and its excellent counterbalance range system can even balance the lightest configuration of a mirrorless camera with a kit lens. In addition, the optimally adjusted drag system provides great operability and smooth start and stop of pan and tilt movements. The NX-100 Series is great for mirrorless cameras, DSLRs, small handheld cameras and light rigged cameras. Operability with Precision Thanks to specially skilled craftsmen in Libec Japan, we adapted an innovative design to maximize NX's performance. As result, a significant reduction in wobbling and backlash in pan and tilt movements is achieved and offers the best precision operability in its range by far. Newly Designed Multistep Counterbalance Mechanism The NX series can support a wide range of camera configurations with a newly designed multistep counterbalance system that fits variety of production styles. Users can select from 5 steps of counterbalance including a zero "free" mode option for speedy set-up. Advanced Drag Unit The layered metal unit in the drag system ensures operability, durability and reliability. This advanced drag unit offers smoother starts, improved backlash control and more rigidity than a conventional low cost plastic unit commonly adapted by other brands. Highly Reliable Multistep Drag System The NX series features the variable 4 step drag pan tilt system that includes a zero "free" mode option with no friction. In addition, the finest silicon grease is applied to ensure ordinary pan and tilt movements at a wide temperature range from -40˚C/-40˚F up to +60˚C/+140˚F. Newly Designed Carbon Legs, Foot Pads and Spreader With a new lightweight structure design, the width of the carbon leg's upper pipe leg is widened to enhance torsional rigidity and provide high payload performance. Developed exclusively for the NX series, the FP-1B foot pads and SP-1B floor spreader are available. The newly designed foot pads and floor spreader are even lighter than the existing model FP-2B and SP-2B. User Friendly Accessory Attachments On the side of the fluid head, there are 1/4 and 3/8 inch screw holes to attach an accessory arm with a monitor or a light. Since the holes are located on the base, the payload capacity, center of gravity and front-rear balance are not affected. Double-sided Serrations Serrations are equipped on both sides of the head to accommodate an additional pan handle or other accessories. Dual Head Dual-head specification is available for both 75mm bowl and flat base tripods. The Dual-head is also compatible with sliders, skater dollies, and photo tripods. Snap ON/OFF Sliding Plate The sliding plate can be attached and released with just one-touch. Easy and smooth settings in the field are easily achieved. Highly Compatible Sliding Plate Compatible with the hands-free monopod "TH-M", the electric gimbal "TH-G3", and other brand camera accessories. The sliding plate allows users to quickly swap between a wide range of camera supports. LED Bubble Level The bubble level is equipped with an LED light to level a tripod in the dark. Safety Design With safety in mind, the tripod legs are carefully designed to prevent the tripod from collapsing on a user's fingers, even if the tripod is collapsed unintentionally. Multi-functional Carrying Case This special carrying case includes a shoulder strap, handles and a zipped pocket.

Libec NH30 75mm Ball and Flat Base Video Head

Libec NH30 (NH-30, NH/30, NH_30, NH 30, nh30) 75mm Ball and Flat Base Video Head User Friendly Accessory Attachments On the side of the fluid head, there are 1/4 and 3/8 inch screw holes to attach an accessory arm with a monitor or a light. Since the holes are located on the base, the payload capacity, center of gravity and front-rear balance are not affected. Double-sided Serrations Serrations are equipped on both sides of the head to accommodate an additional pan handle or other accessories. Dual Head Dual-head specification is available for both 75mm bowl and flat base tripods. The Dual-head is also compatible with sliders, skater dollies, and photo tripods. Snap ON/OFF Sliding Plate The sliding plate can be attached and released with just one-touch. Easy and smooth settings in the field are easily achieved. Highly Compatible Sliding Plate Compatible with the hands-free monopod "TH-M", the electric gimbal "TH-G3", and other brand camera accessories. The sliding plate allows users to quickly swap between a wide range of camera supports.

Libec NH10 75mm Ball and Flat Base Video Head

Libec NH10 (NH-10, NH/10, NH_10, NH 10, nh10) 75mm Ball and Flat Base Video Head User Friendly Accessory Attachments On the side of the fluid head, there are 1/4 and 3/8 inch screw holes to attach an accessory arm with a monitor or a light. Since the holes are located on the base, the payload capacity, center of gravity and front-rear balance are not affected. Double-sided Serrations Serrations are equipped on both sides of the head to accommodate an additional pan handle or other accessories. Dual Head Dual-head specification is available for both 75mm bowl and flat base tripods. The Dual-head is also compatible with sliders, skater dollies, and photo tripods. Snap ON/OFF Sliding Plate The sliding plate can be attached and released with just one-touch. Easy and smooth settings in the field are easily achieved. Highly Compatible Sliding Plate Compatible with the hands-free monopod "TH-M", the electric gimbal "TH-G3", and other brand camera accessories. The sliding plate allows users to quickly swap between a wide range of camera supports.

Libec JB40-KIT Jib Arm Kit with Tripod And Dolly

Libec JB40-KIT (JB40/KIT, JB40_KIT, JB40KIT, JB40 KIT, jb40-kit) Jib Arm Kit with Tripod And Dolly Professional Jib arm with T102B tripod and DL-8RB dolly . JB40 KIT includes Jib arm：JB40, Tripod：T102B, Dolly：DL-8RB, Weight Kit: WEIGHT30 KIT. As the successor to the best selling jib arm JB30, the new JB40 has been redesigned for professionals who can enjoy and appreciate a rigid, compact and lightweight jib arm. The JB40 jib arm is the ideal solution for front operations as it provides outstanding stability and flexibility to users who work with heavy cameras onsite. Simply designed for quick and easy setup, the JB40 enables even the smallest crew to effortlessly and comfortably operate the jib. Buy Libec JB40 KIT from UBMS Dubai. We can provide best price and fast delivery for all Libec products. UBMS is the authorized Libec dealer in Middle East . Rigidity JB40 can support weights up to 20kg and is designed to minimize wobbling or bending of the arm, resulting in smooth and stable camera shots. High Portability When folded and stored in its respective included carrying case, the jib arm is only about 120cm in length and easily fits in the trunk of a car. Although the jib arm only weighs 10kg, the case's shoulder strap offers extra support and reduces the burden of transportation. Compact Design By sliding the main arm, the jib arm becomes remarkably compact with a radius of about one meter, making it perfectly suitable for any production set including sets in tight places. Redesigned Weight Mounting Method By changing the weight bar's design from the former JB-30's Screw-in type to a new Plug-in type for the JB40, assembly and break down time is dramatically decreased. 3-Step Easy Setup Connect the support arms, set the jib on the tripod, and adjust the balance. With only 3 steps, the JB40 is ready for any video production. Compatibility In addition to Libec's 100mm tripods, the JB40 jib arm can also be used with other brand tripods you may already own. 100mm to 75mm Conversion Adapter A 75mm ball base fluid head can be attached by using the included adapter AD-75.

Libec JB40 Jib Arm with Carrying Case

Libec JB40 (JB-40, JB/40, JB_40, JB 40, jb40) Jib Arm with Carrying Case Create smooth, dynamic camera moves with high and low angles using this JB40 Jib Arm with Carrying Case from Libec. This portable and easy-to-use jib has an extendable arm range of 24.8 to 39.5" in length, and it can be easily adjusted using locking levers. The JB40 weighs only 22.7 lb and is easy to set up and break down for transport using its carry case. It features a 100mm tripod base and a 100mm head bowl with an included 75mm attachment, so you can mount a variety of fluid heads onto the jib. A counterweight bar installs on the rear of the arm and one 2.2 lb counterweight is included, with plenty of room for additional, optional counterweights to balance your rig.

Libec LX5 System With Floor Spreader

Libec LX5 (LX-5, LX/5, LX_5, LX 5, lx5) System With Floor Spreader The Libec LX5 Tripod With Pan and Tilt Fluid Head and Floor Spreader delivers superior value with an aluminum tripod and a pan and tilt fluid head. It has a maximum height of 5.45' and a minimum height of 22" (56 cm). It can handle a load of up to 9 lb, and you can trace every motion, start to finish, with its super torque system. The fluid head is equipped with a sliding plate with a sliding range of +/- 1.6". The entire kit weighs 12.1 lb (5.5 kg) lb. The LX5 can operate in a temperature range of -4 to +140°F (-20 to +60°C). This tripod is ideal for small to mid-sized DV and HD video cameras.

Libec RT30B 2-Stage Aluminum Tripod Legs

Libec RT30B (RT-30B, RT/30B, RT 30B) 2-Stage Aluminum Tripod Legs The Libec RT30B 2-Stage Aluminum Tripod Legs feature a 75mm bowl base and support up to 55 lb loads. The height range is a low minimum height of 16" to a maximum height of 59.5". The tripod has spiked feet for use on soft ground, and the aluminum die-cast material used for the upper leg casing enhances overall stability.

Libec TH-X-H Head with Pan Handle

Libec TH-X-H (TH-X/H, TH-X_H, th-x-h) Head with Pan Handle Libec TH-X H, the new entry level high-spec fluid head with a 4kg/9lb payload capacity! It consists of a dual base head and a fixing handle for 65mm bowl tripods. The TH-X H is designed with a dual head structure (flat base/65mm bowl), dual rosettes and includes a Snap On/Off slide plate compatible with Manfrotto and Sachtler heads to maximize production value. Made for today's 4K UHD/HD/DV camcorders and DSLR cameras, it is great for all types of photo/video/DSLR shoots including home videos, documentaries, corporate assignments, weddings & events, nature, sports and journalist news gatherings. Dual head Structure The TH-X Head is designed with a Dual base structure with a 3/8" screw hole compatible with video tripods, photo tripods, monopods, sliders, skater dollies and other equipment with 3/8" screws, making this dual head a multi-functional film tool in a variety of shooting environments. Payload and Counterbalance The TH-X H head supports payloads up to 4kg/9lbs and features a built-in counterbalance for precise camera balance operations allowing users to enjoy professional pan & tilt movements on photo/video shoots. Snap On/Off Sliding Plate Equipped with a one touch attach/release mechanism, the sliding plate slides +/-30mm/1.2" front to rear for swift camera plate adjustments. The TH-X sliding plate includes a 1/4" screw with video pin and allows you to easily adjust your equipment's center of gravity to balance the weight of the camera. As an added benefit, the sliding camera plate is compatible with Manfrotto and Sachtler heads, allowing users to quickly interchange shots between other heads. Strategically positioned knobs for quick setups and adjustments The pan lock, tilt lock and sliding plate lock are all located on the left hand side of the head for quick & easy setups and adjustments while holding the camera and operating the head with your right hand. Lightweight and Versatile Reduced weight of only 1kg/2.2lb including the pan handle and bowl clamp that allows you to attach the head to a 65mm bowl tripod. Dual Rosettes & Bubble Level The TH-X has two pan handle rosettes, one on each side of the head, allowing you to place an additional pan handle for increased control or attaching an AS-7K articulating support arm to mount other video equipment such as a monitor, resulting in higher-quality shots. The head is equipped with a bubble level and has a tilt angle of +90/-80degree.

DL-10RB-COMPACT Dolly for Select Libec, Sachtler & Vinten Tripods

Libec DL-10RB-COMPACT (DL_10RB_COMPACT, DL/10RB/COMPACT, DL 10RB COMPACT) Dolly for Select Libec, Sachtler & Vinten Tripods The DL-10RB Compact Dolly from Libec is a foldable dolly for select Libec, Sachtler, and Vinten video tripods. It features a 242.5 lb payload, locking wheels, and an aluminum structure, along with an integrated carrying handle and detachable cable guards.

Libec T150C Heavy-Duty 2-Stage Carbon Fiber Tripod Legs with 150mm Bowl

Libec T150C (T-150C, T150/C, T150 C) Heavy-Duty 2-Stage Carbon Fiber Tripod Legs with 150mm Bowl The Libec T150C is a heavy-duty set of carbon fiber tripod legs with a 150mm bowl. It supports up to 220.5 lb and offers a height range of 23 to 64" in two legs stages. Each leg has a twist leg lock knob at each stage. The legs feature spiked feet and come with a plastic cover over them. If you incorporate an optional ground spreader, the legs can be installed into the spreader with these plastic covers on. Compatible spreaders include the SP-15B ground spreader and BR-6B mid-level spreader. Optional rubber food pads are also supported, such as the FP-6B pads. The carbon fiber construction is especially suited for users who shoot on the beach or similar outdoor environments because it's corrosion resistant. Multiple 3/8"-16 and 1/4"-20 accessory mount threads are provided on two sides of the tripod, on top near the bowl base. A weight hook is also provided on one of the legs. The T150C is made in Japan. Compatible tripod heads include the Libec QH1 and QH3.

Libec T150B Heavy-Duty 2-Stage Aluminum Tripod Legs with 150mm Bowl

Libec T150B (T150-B, T150/B, T150 B) Heavy-Duty 2-Stage Aluminum Tripod Legs with 150mm Bowl The Libec T150B is a heavy-duty set of aluminum tripod legs with a 150mm bowl. It supports up to 220.5 lb and offers a height range of 23 to 64" in two legs stages. Each leg has a twist leg lock knob at each stage. The legs feature spiked feet and come with a plastic cover over them. If you incorporate an optional ground spreader, the legs can be installed into the spreader with these plastic covers on. Compatible spreaders include the SP-15B ground spreader and BR-6B mid-level spreader. Optional rubber food pads are also supported, such as the FP-6B pads. Multiple 3/8"-16 and 1/4"-20 accessory mount threads are provided on two sides of the tripod, on top near the bowl base. A weight hook is also provided on one of the legs. The T150B is made in Japan. Compatible tripod heads include the Libec QH1 and QH3.

Libec T103C Professional 2-Stage Carbon Fiber Tripod

Libec T103C (T103-C, T103/C, T103 C) Professional 2-Stage Carbon Fiber Tripod The Libec T103C is a professional 2-stage carbon fiber tripod featuring a 100mm bowl base. It supports up to 198 lb, and both leg stages have a double strut design that ensures more stable operation. With an optional SP-6B ground spreader attached, the tripod offers a height range of 24.5 to 68.5". The tripod features spiked feet and supports the optional Libec FP-6B large foot pads, sold separately. It also supports the optional BR-6B mid-spreader.

Libec TH-Z-S8-KIT Fluid Head, Tripod, 33 inch Slider & Carry Case Kit

Libec TH-Z-S8-KIT (TH_Z_S8_KIT, TH/Z/S8/KIT, th-z-s8-kit) Fluid Head, Tripod, 33 inch Slider & Carry Case Kit The Libec TH-Z S8 Kit is a highly flexible system featuring a fluid head that can be mounted directly on the 75mm tripod bowl or attached directly to the slider. This is thanks to the head's dual-function design consisting of a half ball with a flat base. The slider also has a 75mm half ball and can be mounted directly on the tripod as well. The fluid head supports up to 11 lb and features fixed counterbalance and drag and a convenient snap-in camera plate system. The slider provides a 28" travel distance, and the tripod offers a height range of 23 to 58.5". Libec TH-Z H Fluid Head The Libec TH-Z H Fluid Head is a compact dual-function tripod head with an 11 lb payload and fixed counterbalance and drag. It features a native 75mm half ball and has a flat base with a 3/8"-16 mounting thread on the bottom of the half ball. It's directly compatible with 75mm bowl tripods but can also be mounted directly on sliders and other supports via the flat base. A tie-down is included for securing it to tripods. The head has a snap-in camera plate system that lets you attach the included camera plate from above rather than slide it in from the rear. The plate has a sliding range of 1.2" once secured. It comes with a 1/4"-20 mounting screw and an anti-twist video pin beside it. A long rosette-mount pan bar is included and an optional second one is also supported. Libec TH-Z T Aluminum Tripod with Mid-Level Spreader (75mm Bowl) The Libec TH-Z T is a 2-stage aluminum tripod with a 75mm bowl base and built-in mid-level spreader. It supports up to 55 lb and is adjustable from a minimum height of 23" to a maximum height of 58.5". The integrated mid-level spreader is adjustable telescopically. Libec ALX S8 Slider (32.6") The Libec ALX S8 is a 32.6" long camera slider that features an integrated 75mm ball base with a flat bottom, allowing it to be mounted directly to 75mm bowl fluid heads as well as flat-base heads. When used on tabletop or flat surface using, the slider has a maximum load capacity of 33 lb. For smooth and wobble-free operation, the carriage features eight roller bearings positioned on the rail top and along the sides at angles. A spring-loaded friction knob allows you to adjust slide tension, while a brake knob will lock the carriage in place at any point on the rails. Using a supplied hexagon wrench, you can adjust the pushing force that the ball bearing exerts on the rail. At each end of the slider, there are 1/4"-20 and 3/8"-16 threads and a rosette for attaching various accessories. If you will be using the slider on the ground or tabletop, the slider features built-in legs with height-adjustable feet to accommodate non-level terrain. For compact storage, the legs fold up against the side of the slider, securing in place using thumb knobs. Unscrewing the knobs completely allows you to detach the legs completely and swap out the 32.6" rail for separately available 15.5" or 47" rail lengths. Libec RC-10 Tripod Carrying Case (Black) Store, transport, and protect your TH-Z or TH-X tripod with this black RC-10 Carrying Case from Libec. The case features dual carry straps and an exterior zip pocket for accessories.

Libec TH-Z-S4-KIT Fluid Head, Tripod, 15.5 inch Slider & Carry Case Kit

Libec TH-Z-S4-KIT (TH_Z_S4_KIT, TH Z S4 KIT, TH-Z S4 KIT) Fluid Head, Tripod, 15.5 inch Slider & Carry Case Kit The Libec TH-Z S4 Kit is a highly flexible system featuring a fluid head that can be mounted directly on the 75mm tripod bowl or attached directly to the slider. This is thanks to the head's dual-function design consisting of a half ball with a flat base. The slider also has a 75mm half-ball and can be mounted directly on the tripod as well. The fluid head supports up to 11 lb and features fixed counterbalance and drag and a convenient snap-in camera plate system. The slider provides a 12" travel distance, and the tripod offers a height range of 23 to 58.5". Libec TH-Z H Fluid Head The Libec TH-Z H Fluid Head is a compact dual-function tripod head with an 11 lb payload and fixed counterbalance and drag. It features a native 75mm half ball and has a flat base with a 3/8"-16 mounting thread on the bottom of the half ball. It's directly compatible with 75mm bowl tripods but can also be mounted directly on sliders and other supports via the flat base. A tie-down is included for securing it to tripods. The head has a snap-in camera plate system that lets you attach the included camera plate from above rather than slide it in from the rear. The plate has a sliding range of 1.2" once secured. It comes with a 1/4"-20 mounting screw and an anti-twist video pin beside it. A long rosette-mount pan bar is included and an optional second one is also supported. Libec TH-Z T Aluminum Tripod with Mid-Level Spreader (75mm Bowl) The Libec TH-Z T is a 2-stage aluminum tripod with a 75mm bowl base and built-in mid-level spreader. It supports up to 55 lb and is adjustable from a minimum height of 23" to a maximum height of 58.5". The integrated mid-level spreader is adjustable telescopically. Libec ALX S4 Slider (15.5") The Libec ALX S4 is a 15.5" long camera slider that features an integrated 75mm ball base with a flat bottom, allowing it to be mounted directly to 75mm bowl fluid heads as well as flat-base heads. When used on tabletop or flat surface using, the slider has a maximum load capacity of 33 lb. For smooth and wobble-free operation, the carriage features eight roller bearings positioned on the rail top and along the sides at angles. A spring-loaded friction knob allows you to adjust slide tension, while a brake knob will lock the carriage in place at any point on the rails. Using a supplied hexagon wrench, you can adjust the pushing force that the ball bearing exerts on the rail. At each end of the slider, there are 1/4"-20 and 3/8"-16 threads and a rosette for attaching various accessories. If you will be using the slider on the ground or tabletop, the slider features built-in legs with height-adjustable feet to accommodate non-level terrain. For compact storage, the legs fold up against the side of the slider, securing in place using thumb knobs. Unscrewing the knobs completely allows you to detach the legs completely and swap out the 15.5" rail for separately available 32.6" or 47" rail lengths. Libec RC-10 Tripod Carrying Case (Black) Store, transport, and protect your TH-Z or TH-X tripod with this black RC-10 Carrying Case from Libec. The case features dual carry straps and an exterior zip pocket for accessories.

Libec QD-30PD Pedestal System with QH3 Head and P1000 Pedestal

Libec QD-30PD (QD_30PD, QD/30PD, QD 30PD) Pedestal System with QH3 Head and P1000 Pedestal P1000 Pedestal  The P1000 is equipped with the tracking locking mechanism and cable guards which come standard with the large-sized double-wheel 125mm casters. The tracking locking mechanism ensures straight-line movement by locking the caster direction, while the cable guards prevent the wheels from running over the cable during studio production. Flat Base with High Compatibility Not only compatible with Libec heads but other brand heads as well. With optional accessories, ball based heads can also be attached on this pedestal. Easy-read Air Pressure Gauge Air pressure can be easily checked with the air pressure meter. Drag Knob for Upper Column Adjustment Upper column friction can be adjusted to preferred settings with the drag knob. Mid Column with Gas Spring Assist The gas spring inside the P1000 pedestal supports the mid column's elevation, allowing safe and easy height adjustments and setups with heavy equipment. High Performance Casters with Track Lock Mechanism Large High performance 125mm casters are equipped along with removable cable guards. The casters has a track lock mechanism which allows users to set and move the dolly in three different modes: Free Mode, Tracking Mode and Steer Mode. The caster's locking sound is minimal. Easy to Transport Design The P1000 can be easily disassembled into the P1000 Column, the steering handle and the dolly. This makes the P1000 easy to transport within studios and outside broadcast sites. QH-1 Head Smooth Counterbalance System The Smooth Counterbalance System is a unique Libec technology that allows the counterbalance knob to be adjusted with constant motion to smoothly reach the minimum and maximum power range. The foldaway knob is designed for easy speedy adjustments. Counterbalance Meter The counterbalance power level can be easily viewed by looking at the Counterbalance Meter, allowing users to keep an eye on their preferred counterbalance settings. Center Tilt Lock with High Safety For the camera system's safety, the head can be physically locked into a center tilt position. Even at a distance, the arrow shaped knob and Lock / Unlock symbols are visible. Flat Base and 150mm Ball Base Adapter The BL-150 ball base adapter, which converts the flat base head into a 150mm ball head, is included with the kit. 1/4" and 3/8" Screw Holes for Accessory Attachments Each side of the tripod has three screw holes for accessory attachments. New Leg Lock Knob Design The newly designed leg lock knob are easy to turn, allowing users to adjust tripod legs quickly and firmly.

Libec P1000 150mm Flat Base Pedestal System

Libec P1000 (P-1000, P/1000, P 1000) 150mm Flat Base Pedestal System The P1000 is equipped with the tracking locking mechanism and cable guards which come standard with the large-sized double-wheel 125mm / 4.9" casters. The tracking locking mechanism ensures straight-line movement by locking the caster direction, while the cable guards prevent the wheels from running over the cable during studio production.

Libec QD-10PD Pedestal System with QH1 Head and P1000 Pedestal

Libec QD-10PD (QD_10PD, QD/10PD, QD 10PD) Pedestal System with QH1 Head and P1000 Pedestal P1000 Pedestal  The P1000 is equipped with the tracking locking mechanism and cable guards which come standard with the large-sized double-wheel 125mm casters. The tracking locking mechanism ensures straight-line movement by locking the caster direction, while the cable guards prevent the wheels from running over the cable during studio production. Flat Base with High Compatibility Not only compatible with Libec heads but other brand heads as well. With optional accessories, ball based heads can also be attached on this pedestal. Easy-read Air Pressure Gauge Air pressure can be easily checked with the air pressure meter. Drag Knob for Upper Column Adjustment Upper column friction can be adjusted to preferred settings with the drag knob. Mid Column with Gas Spring Assist The gas spring inside the P1000 pedestal supports the mid column's elevation, allowing safe and easy height adjustments and setups with heavy equipment. High Performance Casters with Track Lock Mechanism Large High performance 125mm casters are equipped along with removable cable guards. The casters has a track lock mechanism which allows users to set and move the dolly in three different modes: Free Mode, Tracking Mode and Steer Mode. The caster's locking sound is minimal. Easy to Transport Design The P1000 can be easily disassembled into the P1000 Column, the steering handle and the dolly. This makes the P1000 easy to transport within studios and outside broadcast sites. QH-1 Head  Smooth Counterbalance System The Smooth Counterbalance System is a unique Libec technology that allows the counterbalance knob to be adjusted with constant motion to smoothly reach the minimum and maximum power range. The foldaway knob is designed for easy speedy adjustments. Counterbalance Meter The counterbalance power level can be easily viewed by looking at the Counterbalance Meter, allowing users to keep an eye on their preferred counterbalance settings. Center Tilt Lock with High Safety For the camera system's safety, the head can be physically locked into a center tilt position. Even at a distance, the arrow shaped knob and Lock / Unlock symbols are visible. Flat Base and 150mm Ball Base Adapter The BL-150 ball base adapter, which converts the flat base head into a 150mm ball head, is included with the kit. 1/4" and 3/8" Screw Holes for Accessory Attachments Each side of the tripod has three screw holes for accessory attachments. New Leg Lock Knob Design The newly designed leg lock knob are easy to turn, allowing users to adjust tripod legs quickly and firmly.  

Libec TH-Z-H Fluid Head

Libec TH-Z-H (TH/Z/H, TH_Z_H, th-z-h) Fluid Head The Libec TH-Z H Fluid Head is a compact dual-function tripod head with an 11 lb payload and fixed counterbalance and drag. It features a native 75mm half ball and has a flat base with a 3/8"-16 mounting thread on the bottom of the half ball. It's directly compatible with 75mm bowl tripods but can also be mounted directly on sliders and other supports via the flat base. A tie-down is included for securing it to tripods. The head has a snap-in camera plate system that lets you attach the included camera plate from above rather than slide it in from the rear. The plate has a sliding range of 1.2" once secured. It comes with a 1/4"-20 mounting screw and an anti-twist video pin beside it. A long rosette-mount pan bar is included and an optional second one is also supported.

Libec QD-10 Tripod System with Ground Spreader

Libec QD-10 (QD_10, QD/10, QD 10) Tripod System with Ground Spreader The Libec QD-10 Tripod System features the pedestal-capable QH1 4-bolt flat base fluid head and the T150B 2-stage aluminum tripod. The system is complete with the SP-15B Ground Spreader, which has individually adjustable arms. The QH1 head attaches to the tripod via an included 150mm half-ball adapter and supports up to 88 lb. It has a side-mount camera plate system and comes with two telescoping pan bars. For attaching accessories, the T150B tripod offers a total of six 1/4"-20 and 3/8"-16 mounting threads around the bowl base. Libec QH1 Fluid Head The Libec QH1 Fluid Head is a pedestal-capable heavy-duty head supporting up to 88 lb. It features a 4-bolt flat base and comes with a 150mm half ball adapter that secures via four included screws. The QH1 has a side-mount camera plate system and includes a sliding plate with dual 3/8"-16 threaded mounting screws. The head also comes with two 2-piece telescoping pan bars that allow for easier integration of optional zoom controllers. Other features include continuous counterbalance, 7-step drag, independent pan and tilt locks, and an illuminated bubble level. Libec T150B Heavy-Duty 2-Stage Aluminum Tripod Legs with 150mm Bowl The Libec T150B is a heavy-duty set of aluminum tripod legs with a 150mm bowl. It supports up to 220.5 lb and offers a height range of 23 to 64" in two legs stages. Each leg has a twist leg lock knob at each stage. The legs feature spiked feet and come with a plastic cover over them. If you incorporate an optional ground spreader, the legs can be installed into the spreader with these plastic covers on. Compatible spreaders include the SP-15B ground spreader and BR-6B mid-level spreader. Optional rubber food pads are also supported, such as the FP-6B pads. Multiple 3/8"-16 and 1/4"-20 accessory mount threads are provided on two sides of the tripod, on top near the bowl base. A weight hook is also provided on one of the legs. The T150B is made in Japan. Compatible tripod heads include the Libec QH1 and QH3. Libec SP-15B Ground Spreader for T150B & T150C Tripods  The Libec SP-15B Ground Spreader is compatible with the Libec T150B and T150C tripods. The arms are individually length-adjustable when you loosen dedicated knobs, and a pull ring is provided in the center for collapsing the spreader.

Libec TH-Z Tripod System with Mid-Level Spreader (75 mm)

Libec TH-Z (TH_Z, TH/Z, THZ, th-z) Tripod System with Mid-Level Spreader (75 mm) The Libec TH-Z Tripod System features a 75mm half ball/flat base fluid head and aluminum 2-stage tripod with a built-in spreader. It also includes a zippered soft carrying case. The head supports up to 11 lb and features fixed counterbalance and drag. It can be attached directly to the tripod or mounted directly on sliders and other support gear via the flat base, which has a 3/8"-16 mounting thread on the bottom. The head also has a snap-in camera plate system that allows for easier attachment of your camera. A pan bar is included and an optional second one is supported. The height range for the head and tripod combined is 28 to 63.5". Libec TH-Z H Fluid Head The Libec TH-Z H Fluid Head is a compact dual-function tripod head with an 11 lb payload and fixed counterbalance and drag. It features a native 75mm half ball and has a flat base with a 3/8"-16 mounting thread on the bottom of the half ball. It's directly compatible with 75mm bowl tripods but can also be mounted directly on sliders and other supports via the flat base. A tie-down is included for securing it to tripods. The head has a snap-in camera plate system that lets you attach the included camera plate from above rather than slide it in from the rear. The plate has a sliding range of 1.2" once secured. It comes with a 1/4"-20 mounting screw and an anti-twist video pin beside it. A long rosette-mount pan bar is included and an optional second one is also supported.

Libec QH3 Fluid Head

Libec QH3 (QH-3, QH/3, QH 3, qh3) Fluid Head The Libec QH3 Fluid Head is a pedestal-capable heavy-duty head supporting up to 152 lb. It features a 4-bolt flat base and comes with a 150mm half ball adapter that secures via four included screws. The QH3 has a side-mount camera plate system and includes a sliding plate with dual 3/8"-16 threaded mounting screws. The head also comes with two 2-piece telescoping pan bars that allow for easier integration of optional zoom controllers. Other features include continuous counterbalance, 7-step drag, independent pan and tilt locks, and an illuminated bubble level.  

Libec QH1 Fluid Head

Libec QH1 (QH-1, QH/1, QH_1, qh1) Fluid Head The Libec QH1 Fluid Head is a pedestal-capable heavy-duty head supporting up to 88 lb. It features a 4-bolt flat base and comes with a 150mm half ball adapter that secures via four included screws. The QH1 has a side-mount camera plate system and includes a sliding plate with dual 3/8"-16 threaded mounting screws. The head also comes with two 2-piece telescoping pan bars that allow for easier integration of optional zoom controllers. Other features include continuous counterbalance, 7-step drag, independent pan and tilt locks, and an illuminated bubble level.

Libec RHP85 Fluid Head

Libec RHP85 (RHP-85, RHP/85, RHP 85) Fluid Head The Libec RHP85 Fluid Head with PH-8B Extendable Pan Handles features the fully adjustable Continuous Counterbalance technology. It offers optimal counterbalance, as well as Balance Stabilizer Mechanism that prevents the slightest wobble on your image, while providing a smooth balancing system. The Fluid Head features a 7-step pan and tilt torque switch that covers a wide torque range. The one-touch attachment and release ensures that the camera plate can be attached and detached with just a touch, enabling fast and easy setup. The Fluid Head comes with the PH-8B Pan Handle with rubber grip that can stop the camera precisely at any tilt angle. The Fluid Head is capable of operating at temperature of -40°F. The Fluid Head features a 100mm diameter ball head. It is designed for use with ENG (Electronic News Gathering) cameras that can capture fast moving objects. It is capable of handling a payload of 55 lb.

Libec TR-320 Tracking Dolly Rail System

Libec TR-320 (TR_320, TR/320, TR 320) Tracking Dolly Rail System The TR-320 includes a set of 80cm/31.5" aluminum pipes to construct a 320cm/126" tracking rail. The dolly offers high-performance bearings and a specialized tracking system to prevent derailing. This allows smooth moving shots on either straight or curved rails. With a simple screw-in mechanism, pipes can be easily and firmly assembled, which enables a quick set up. The CR-90 curved rail and the EX-160S straight extension rails are also available, which offers more shooting flexibility.     

Libec RSP-850M Professional Aluminum Tripod System with Mid-Level Spreader

Libec RSP-850M (RSP_850M, RSP/850M, RSP 850M) Professional Aluminum Tripod System with Mid-Level Spreader The Libec RSP-850M Professional Aluminum Tripod System offers comfort of operation and the ability to capture quick, slow, vertical, and diagonal shots. It allows precise controllability for capturing every single movement. This system is user-friendly for situations that involve setup, shooting, and transportation. The variable counterbalance system enables the tripod fluid head to accommodate many different types of video cameras up to 55 lb (25kg). In addition, a drag system, low-temperature characteristics, and a rigid tripod will meet your video expectations.

Libec LX10-Studio System with dolly

Libec LX10-Studio (LX10/Studio, LX10_Studio, LX10 Studio, lx10-studio) System with dolly The Libec LX10 Studio Two-Stage Aluminum Tripod System and H65B Head with Dual Pan Handles and Spreader Dolly supports cameras and accessories weighing up to 11 pounds. The head and legs feature a 100mm ball/bowl, which provides a wide platform for stable shots. The legs are made from aluminum and feature three leg sections. The head and legs come with a spreader dolly, and the system is height-adjustable from 36 to 73.5". To aid in leveling your shot, a bubble level is incorporated into the head. The head also features a sliding baseplate that allows you to adjust the balance of your camera. It provides fixed counterbalance that helps the fluid head support loads up to 35 pounds. With individual fluid drag adjustments for both pan and tilt, you can adjust the fluid head to suit your shooting style or the needs of the shot. The head features discreet pan and tilt locks, and the removable pan handle can be attached to either side of the head by via the built-in rosettes.