IDX VL-4X System Technology VL-4X 4-Channel V-Mount Charger with Power Supply

IDX VL-4X (VL_4X, VL/4X, VL 4X) System Technology VL-4X 4-Channel V-Mount Charger with Power Supply The VL-4X 4-Channel V-Mount Charger with Power Supply from IDX supports lithium-ion V-mount batteries and features sequential charging for four batteries, automatically switching to the second battery after fully charging the first, and it features simultaneous charging for two batteries when on opposite sides. It delivers up to 2.7A of quick-charge current without the noise of a typical charger thanks to a fanless design. This portable desktop charger is designed with reliable internal safety features that protect both the battery and charger from damage should faulty or misused batteries be placed on the charger. It will automatically stop charging if any attached battery reaches an overvoltage condition. It features a support stand to keep the charger upright on a flat surface.

IDX A-MT2V Male V-Plate Adapter

IDX A-MT2V (A-MT2V, A MT2V, AMT 2V, A/MT2V) Male V-Plate Adapter The A-MT2V is a male V-Mount Adaptor plate designed to make equipment easily adapt to V-Mount with a robust and secure connection.

IDX VL-DT1 Advanced Port Battery Charger

IDX VL-DT1 (VLDT1, VL DT1, VL/DT1) Advanced Port Battery Charger The VL-DT1 is a single channel, low cost, portable charger designed to charge batteries with an D-Tap Advanced port. The D-Taps Advanced three pin design monitors the cell status to ensure correct, controlled charging which prolongs battery life.

IDX VL-2000S Simultaneous Quick Charger with 100W DC Output - 2ch

IDX VL-2000S (VL 2000S, VL2000S, VL/2000S) Simultaneous Quick Charger with 100W DC Output - 2ch The VL-2000S is a fully simultaneous 2-channel Li-ion V-Mount battery charger with a 100W DC output (4-pin XLR). Supporting LIFE PLUS mode, the latest advances in charging technology, the VL-2000S can extend battery life up to 20%. The VL-2000S features Power Base mode – the ability to utilize the mounted batteries for powering equipment via the 4pin XLR output. Low voltage batteries are safely charged with the ‘Recovery Charge’ mode. The charger also houses energy efficient circuitry that will automatically power down the charger when inactive.

IDX VL-2X 2 Channel Endura Fully Sequential Charger

Idx VL-2X (VL2X, VL 2X, VL/2X, vl-2x) 2 Channel Endura Fully Sequential Charger with built-in AC Adaptor (36W) 2-Channel V-Mount Charger & Power Supply  The VL-2X delivers slim, lightweight 2-channel charging with the added advantage of an integrated 36W power supply. With a new fanless design, the VL-2X also delivers high power charging without the noise of a typical quick charger. The VL-2X is a multi-chemistry charger for both Li-ion and Ni-Cad battery types. Sequential 2-channel charging in either position. The VL-2X will charge the first battery connected to either VMount channel, automatically switching to charge the second battery after the first is fully charged. Integrated 36W DC power supply provides 36W XLR output for the camera, lighting or ancillary broadcast devices. Compact, lightweight charger body (3.4inches in width / 0.97lbs in weight) Advanced fanless design Integrated locking support stand Internal safety features protect both the battery and charger from serious damage should faulty or misused batteries be placed on charge. The VL-2X will automatically stop charging should any battery reach an over voltage condition.   System includes 60W AC-Adaptor Power Supply for power

IDX SL-VBD96 7.2V Li-Ion Battery for Panasonic Cameras

IDX SL-VBD96 (SL_VBD96, SL/VBD96, SL VBD96) 7.2V Li-Ion Battery for Panasonic Cameras The SL-VBD96 7.2V Li-Ion Battery from IDX is designed for select Panasonic cameras. With 9600mAh capacity, the battery provides extended runtimes on cameras such as the AG-DVX200 and AJ-PX270. It comes standard with an X-Tap and USB power ports to power camera accessories and USB devices. With a 4-LED power status indicator, users can easily identify the charge level.

IDX C-ZLPRO Cine Servo DC Cable for Canon Cine Cameras

IDX C-ZLPRO (CZLPRO, C ZLPRO, C/ZLPRO, c-zlpro) Cine Servo DC Cable for Canon Cine Cameras.C-ZLPRO has been created to fulfill the demand for a means to power Canon’s CINE-SERVO zoom lenses with cameras that would otherwise not have the ability– due to lacking a DC power supply to the lens. The C-ZLPRO has a D-Tap plug to HR10 10J- 12S connector and is 18” long. It allows 12- 17V DC to be supplied either directly from batteries such as the ENDURA DUO or CUE series, or from the D-Tap output from IDX ENDURA VMount plates.

IDX ET-PV2UR V-Mount Battery Adapter for Blackmagic URSA Camera

IDX ET-PV2UR (ET_PV2UR, ET/PV2UR, ET PV2UR) V-Mount Battery Adapter for Blackmagic URSA Camera IDX continue to develop the latest accessories for Broadcast and Cine cameras with a V-Mount power solution for the Blackmagic URSA Camera, the ET-PV2UR. The ET-PV2UR is designed to attach directly to the rear of the URSA camera body. Based on the popular IDX V-Plate chassis, the ET-PV2UR allows direct mounting of any high capacity IDX ENDURA Lithium Ion battery. In consideration of the high current draw of the URSA; IDX recommend the following batteries for this application, Elite, E-HL9, E-HL9S, DUO-150 and CUE-D150.The ET-PV2UR also contains an unregulated D-Tap output to allow the use of professional on-board camera lights and other accessories.

IDX BH-2 ENDURA ELITE Battery Housing

IDX BH-2 (BH2, BH 2, BH/2, bh-2) ENDURA ELITE Battery Housing. IDX BH-2 (BH2) ENDURA ELITE Battery Housing Only. PLEASE NOTE: This item is the Housing Only - Cartridges are NOT included.  

IDX JP-2 Kit with 2x SSL-JVC75 Batteries and 1x LC-2J Charger

IDX JP-2 (JP_2, JP/2, JP 2) Kit with 2x SSL-JVC75 Batteries and 1x LC-2J Charger The SSL-JVC75 Lithium-Ion Battery  IDX has partnered with JVC to manufacture a high capacity Li-ion battery, designed specifically for use with the GY-HMQ10U and GY-HM600 Series Camcorders.   The SSL-JVC75 is a high capacity 7.4V, 7350mAh, 55Wh Li-ion battery  LC-2J 7.4V 2-Channel Simultaneous Quick Charger for SSL-JVC50 and SSL-JVC75 batteries The LC-2J is a 2-Channel simultaneous quick charger for the IDX SSL-JVC50 Li-ion battery.  Each channel is operated independently, so batteries can be placed on charge in any order and at any time for a quick turnaround.  The LC-2J has an ultra compact footprint, but multiple LC-2J units can be connected to create a solid charging base is required.  

IDX LC-2J 2 Channel Charger for JVC SSL-JVC50 and SSL-JVC75

IDX LC-2J (LC_2J, LC/2J, LC 2J) 2 Channel Charger for JVC SSL-JVC50 and SSL-JVC75 LC-2J 7.4V 2-Channel Simultaneous Quick Charger for SSL-JVC50 The LC-2J is a 2-Channel simultaneous quick charger for the IDX SSL-JVC50 Li-ion battery.  Each channel is operated independently, so batteries can be placed on charge in any order and at any time for a quick turnaround.  The LC-2J has an ultra compact footprint, but multiple LC-2J units can be connected to create a solid charging base is required.

IDX SSL-JVC75 7.4V Battery System

IDX SSL-JVC75 (SSL_JVC75, SSL/JVC75, SSL JVC75) 7.4V Battery System This high-capacity IDX Battery from JVC is designed for the JVC GY-HM600U, GY-HM650U, and GY-HMQ10U cameras and JVC DT-X series monitors. It features a 7.4V output and 55Wh capacity and offers a proprietary IDX 7.2V X-Tap output for powering various accessories simultaneously with the camera/monitor. The optional C-XTAP2 X-Tap open leads cable is required for using the X-Tap connector.

IDX SD-1E Endura Single Position Power Unit 7.2V / 12V Output

IDX SD-1E (SD1E, SD 1E, SD/1E) Endura Single Position Power Unit 7.2V / 12V Output The SD-1E is another small profile V-Mount bracket which can be attached to any standard waist belt and will support up to two ENDURA batteries in PowerLink mode. Customers have a choice of simultaneous 7.2V (regulated) and/or 12V (unregulated) output to a camera or other portable equipment. The power output is via a 4-pin XLR connector.

IDX MD-NBV Multi D-Tap V-Mount Adapter Plate

IDX MD-NBV (MD_NBV, MD/NBV, MD NBV) Multi D-Tap V-Mount Adapter Plate Designed to be sandwiched between a V-Mount camera and battery or mounted on a V-Dock, the MD-NBV, has five (5) D-Taps and allows you to power accessories such as onboard monitors, lights, wireless receivers, media recorders, signal converters, etc. Max draw from each D-Tap is 24W/2A (each D-Tap independently fused), and total Max draw is 120W/10A.

IDX A-CP(A) Universal Cheese Plate and 15mm Clamp Adapter

IDX A-CP(A) (A/CP(A), A CP(A), A_CP(A) a-cp(a)) Universal Cheese Plate and 15mm Clamp Adapter. The A-CP(A) aluminum cheese plate and clamp allows to attach IDX V-Mount P-V2 series plates on rod system in variety of mounting positions. Compatible with P-V2, P-VS2, P-V257, P-V284, P-V212, A-E2EOSC and ET-PV2BM for powering various cameras on a rod system. 

IDX A-E2EOSC V-Mount Plate for Canon C300 / C500

IDX A-E2EOSC (AE2EOSC, A E2EOSC, A/E2EOSC, a-e2eosc) V-Mount Plate for Canon C300 / C500. IDX continues to expand its accessory line to power mid sized digital broadcast and cinema cameras. The new A-E2EOSC allows IDX ENDURA batteries to power Canon Cinema EOS cameras C100, C300, and C500.

IDX P-V284 Endura V-Mount Plate

IDX P-V284 (PV284, P V 284, P/V284) Endura V-Mount Plate The IDX P-V284 Endura V-Mount Plate is a 2-pin D-tap DC Out and DigiView plate that is an enhanced variation of the P-V2 Plate series. Providing an ideal solution for combining Endura V-Mount batteries to handheld cameras without the standard V-Mount style battery lock, the plate offers precise DC power connectivity. For camera systems compliant with DigiView, the remaining battery power can be displayed in the viewfinder. Featuring dual 2-pin D-taps, the plate uses 1 tap for regulated 8.4V. The second D-tap offers up to 16.8V (for IDX Lithium ion batteries) unregulated battery throughput for equipment such as lights and HDD recorders. You can use the Endura V-Mount Plate for a variety of cameras using the optional IDX cables specific to the camera models. The maximum power output available from the plate is 50W, and it measures 3.25 x 5.59 x .47" and weighs 0.40 lb.

IDX P-V212 V-Mount Plate with 2 x 2-pin D-Tap Outputs

IDX P-V212 (P_V212, P/V212, P V212) V-Mount Plate with 2 x 2-pin D-Tap Outputs The P-V212 regulates the 14.4V input from an ENDURA V-Mount Li-ion battery to output 12V, suitable for use with cameras that require this input voltage for operation. A second D-Tap connector is included. As a variation of the popular P-V2 Plate series, the P-V212 provides to the 12VDC output and includes dual D-Taps – one positioned on each side: one 2-Pin D-Tap for regulated 12VDC output and a second D-Tap for unregulated battery throughput (lights, HDD recorder, etc.).  

IDX P-V257 Endura V-Mount Plate

IDX P-V257 (PV257, P V 257, P/V257) Endura V-Mount Plate The P-V257 regulates the 14.4V input from an ENDURA V-Mount Li-ion battery to output 5V or 7.3V. The choice of output depends on the input voltage required for the camera, and can be chosen via a power select switch on the side of the unit. A second D-Tap connector is located on the opposite side which can be used to power optional camera accessories.

IDX A-AB2E V-Mount Adapter Plate

IDX A-AB2E (AAB2E, A AB2E, A/AB2E, a-ab2e) V-Mount Adapter Plate. IDX A-AB2E (AAB2E) Adaptor Bracket to fit Endura Batteries to Anton Bauer Camera Mount. This adapter locks onto 3-stud mounting plates as a temporary or transitional 3-stud converter to a V-Mount configuration. The flexibility of the converter allows ENDURA system batteries to be used on 3-stud mounting systems. Please note that when using the A-AB2E, the Digi-View function becomes disabled.

IDX A-E2LCD-2 Adaptor Bracket to Fit ENDURA Batteries

IDX A-E2LCD (AE2LCD2 A E2LCD 2 A/E2LCD/2, a-e2lcd-2) Adaptor Bracket to fit ENDURA Batteries to Panasonic LCD Monitor.A-E2LCD-2 is compatible with various LCD monitors using the industry standard VESA 100 base.  Power to the LCD is provided via the adaptor’s 4-pin pigtail XLR female connector. Please check with IDX for confirmation of LCD model compatibility.

IDX A-E2NP NP Battery Adapter

IDX A-E2NP (AE2NP, A E2NP, A/E2NP, a-e2np) NP Battery Adapter - for Endura V Series. DX A-E2NP (AE2NP) Adaptor to charge IDX NP-L7 Batteries on ENDURA Chargers. The A-E2NP is an adaptor for charging IDX NP-type Lithium Ion batteries on an ENDURA V-Mount charger.  

IDX C-EB(XLR) V-Mount Battery Discharge Adaptor

IDX C-EB(XLR) (CEB(XLR) C EB(XLR) C/EB(XLR) c-eb(xlr)) ENDURA V-Mount Battery Discharge Adaptor. C-EB(XLR) is a small compact power adaptor which can be attached to any standard waist belt and will support up to two ENDURA batteries, including PowerLink mode.  It can be used in many applications to power broadcast and audio equipment.   The power output is via a 4-pin XLR connector.

IDX JL-2Plus 2 Ch. Sequential Fast Charger for NP Li-ion & NiCd

IDX JL-2PLUS (JL2Plus JL 2 Plus JL/2Plus) 2-Channel, Sequential NP Quick Charger with AC Adaptor (60W)    The best way to extend the operational life of IDX NP-style Lithium Ion batteries is to use the JL-2PLUS, which charges 2 IDX NP-style Li-ion or IDX NP-style Ni-CD batteries sequentially with unrivalled high speed and reliability.    The JL-2PLUS has the advantage of an integrated 60W power supply for the camera and additional equipment.    The JL-2PLUS can charge ENDURA batteries using an optional C-NP2E adaptor making it the perfect charger for Ni-Cd users to upgrade to Li-ion.

IDX P-V2 Endura V-Mount Plate with 2 Pin D-Tap DC Out

IDX P-V2 (P_V2, P/V2, P V2) Endura V-Mount Plate with 2 Pin D-Tap DC Out ENDURA V-Mount Plate with 2 Pin D-Tap DC Out & Digi-View The P-V2 V-Mount adaptor plate converts most cameras to a V-Mount battery interface. Multiple mounting holes fit virtually all professional video cameras as well as many manufacturers’ monitors, hard drives, test instruments and more. The P-V2 has a 2 pin D-Tap on the side for powering an on-board camera light or accessories. As part of IDX’s Dig-View feature, digital battery data from the ELITE, E-HL9, E-10 and E-7 can be transferred through the P-V2 to viewfinders of compatible cameras.

IDX P-VS2 V-Mount Battery Plate

IDX P-VS2 (PVS2, P VS 2, P/VS2) V-Mount Battery Plate The P-VS2 plate converts almost any camera to a V-Mount battery connection, with multiple mounting holes to fit cameras of any manufacturer. The P-VS2 includes a 2 pin D-Tap on the side to connect an on-board camera light and also features Syncron, which turns the on-board light on and off in sync with camera record button. As part of IDX's Digi-View feature, digital battery data from the ENDURA ELITE, E-10 and E7 can be transferred through the P-VS2 to compatible view finder cameras.

IDX P-VS2PW V-Mount Camera Converter

IDX P-VS2PW (P_VS2PW, P/VS2PW, P VS2PW) V-Mount Camera Converter  IDX's P-VS2PW plate has been designed specifically for the Panasonic AJ-HPX3100. The P-VS2PW features an additional power connector, to be attached to the camera before mounting in position, which allows the power tap on the AJ-HPX3100 camera to draw DC power from an attached V-Mount battery. The P-VS2 includes a 2 pin D-Tap on the side to connect an on-board camera light and also features Syncron, which turns the on-board light on and off in sync with camera record button. As part of IDX's Digi-View feature, digital battery data from the ENDURA ELITE, E-10 and E-HL9 can be transferred through the P-VS2PW to compatible view finder cameras.

IDX Vl-2Plus 2 Ch. ENDURA Sequential Fast Charger

IDX VL-2PLUS (Vl2Plus Vl 2Plus Vl/2Plus) 2-Channel, Sequential V-Mount Quick Charger with AC Adaptor (60W)    The lightweight and durable VL-2PLUS delivers sequential 2-channel charging with unrivalled high speed and reliability.    The VL-2PLUS has the advantage of an integrated 60W power supply for the camera and additional equipment.    The VL-2PLUS is a multi-chemistry charger, with the ability to charge NP type batteries using an optional A-E2NP adaptor.