Hague Long Articulating Arm Kit With Nano Clamp

Hague LAAKIT (LAA_KIT, laa_kit, laa-kit, laa/kit) Long Articulating Arm Kit With Nano Clamp The Hague Articulating Arm is ideal when used with the Nano Clamp or the Hot Shoe Adaptor to mount a monitor, sound recorder or other accessory to a tripod leg or the shoe of the camera. If the Arm is attached to the Nano Clamp it can be used to fasten a small camera to cycle, pole, table edge, etc. The Arm will support up to 1kg. It has 1/4-20 studs on both ends. All pivot points are locked by a single handwheel.

Hague HD90 Heavy Duty 90° Right Angle Tripod Camera Mount

Hague HD90 (hd-90, HD_90, HD-90, hd_90) Heavy Duty 90° Right Angle Tripod Camera Mount The Hague Heavy Duty 90° Right Angle Tripod Camera Mount has been designed for people looking to shoot in portrait mode and is suitable for a wide variety of camera set-ups. It allows you to mount the camera at a 90 degrees angle on your own tripod and is ideal for portrait filming.  The bracket has a variety of threaded holes to mount it to the tripod’s camera plate in various positions, 13 x ¼” and 17 x 3/8”. The camera can be mounted to the angle plate using either mounting holes or the slots; there are 7 x ¼” holes, 3 x 3/8” and 2 slots. The bracket is supplied with 2 x ¼” camera screws and 2 x 3/8” camera screws.

Hague LEV Levitator Stabilizer

Hague LEV (L-E-V, l/e/v, L_E_V, lev) Levitator Stabilizer The Hague Levitator is a camera support system similar to a Camframe or Fig Rig, but which has the stabilizing effect of a Steadicam. Like the Fig Rig the support is held by both hands, but the Levitator’s handles are totally free moving and the camera is self balancing, similar to a Steadicam but without the need for counterbalance weights. It’s this combination that gives the camera a levitating effect as if it is floating through the air. The Levitator uses the camera’s own weight for counterbalance, so there is no need for counterbalance weights as used on most “Steadicam type” stabilizers. This reduces the weight of the support and the twin handle design makes it easier to hold for long periods. Once the camera is balanced, the Levitator gives the camera a truly floating effect with easy directional and tilt control with the two handles. As there is very little restriction above or below the camera, the Levitator can simply skim over or under items creating shots unattainable from other devices. The sealed radial bearings in the pivot cups and the ball socket handles reduce hand movement as you move around. It’s quick and simple to set up and the quick release camera plate makes it easy to get your camera on and off the support. Extra mounting holes and a cold shoe enables you to attach any extra accessories to the Levitator. The supplied rigging stands make it easy to adjust the Levitator’s fine trim controls until optimum balance is achieved. Also included is a Balance Correction Adapter, this is only required when heavy lenses are mounted to the camera making it very front heavy, or accessories are mounted to the camera that may affect the cameras centre of balance.  

Hague HP1 Highshot Camera Pole 6M

Hague HP1 (HP_1, hp-1, hp_1, hp/1) Highshot Camera Pole 6M The Hague 6m Highshot Camera Pole is made from lightweight glass fibre and allows you to quickly capture elevated photos or video footage. The HP1 Highshot pole is constructed from high quality composite materials and is finished with an acrylic resin making it an economical and portable solution which supports up to 2kg. The Hague telescopic Highshot poles are a great way to quickly achieve height and are ideal for property photography, site surveys or sports filming. The system is supplied with a tilt head attached to the top which allows you to angle the camera position and you can then rotate the whole pole. The tilt head incorporates a quick release camera plate, with a standard ¼” camera screw attachment, and this makes it easy to quickly add or remove the camera. The telescopic Highshot pole is supplied with a high quality footplate which allows for smooth rotation of the pole when elevated and this folds up neatly for transport. This helps with the stability and usability of the pole. Optional extras, listed below, include clamps and brackets which allow the user to mount viewing monitors, tablets or phones to the pole so you can easily see what you are capturing or to control the camera functionalities. Comprising of four sections the HP1 extends to 6m yet reduces down to 1.75cm for transit and is supplied in a padded transit bag.

Hague BMS75 Bowl Mount 75mm with Superclamps

Hague BMS75 (BM-75, BM/75, bm75) Bowl Mount 75mm with SuperclampsThe Hague 75mm bowl mount gives a rigid platform onto which you can attach your video head.Suitable for 75mm bowl type tripod heads the BM75 Bowl Mount has two 5/8" spigots on the bottom which allows it the be attached to items with a 5/8" socket, such as a Superclamp.Colour - Black.Supports up to 16kg.

Hague Ceiling Mount With Double Ball Bracket

Hague WB2 (WB-2, WB/2, WB_2, WB 2) Ceiling Mount With Double Ball Bracket The Hague WB2 wall/ceiling mount with a double ball tilt head can be screwed to a ceiling, wall, or table. The double ball bracket is fully adjustable with a single lever for locking. A reversible camera plate enables the camera to be mounted above or below the fixing point.

Hague Superclamp With Double Ball Tilt Head

Hague SC2 (SC-2, SC/2, sc2) Superclamp With Double Ball Tilt Head The Hague SC2 Superclamp with Double Ball Tilt Head is ideal for mounting a camera onto a vehicle, rod or post as it is fully adjustable and can be mounted either horizontally or vertically. On cars it can be fastened to a rollbar, roof rails or a roof rack. The Superclamp & Double Ball Tilt Head can be attached to a pole, tube, bench or table. Its jaws will attach to anything between 12 to 55mm in width. It can be fixed either vertically or horizontally. The Double Ball Tilt Head with a reversible camera plate can be set at any angle or direction with a single lever for locking. It's ideal for all types of cameras up to 3kg.

Hague SC1 Superclamp With Ball Levelling Head For Cameras

Hague SC1 (SC-1, SC/1, sc1) Superclamp With Ball Levelling Head For CamerasThe Hague SC1 Superclamp with Ball Leveller can be used to secure the camera to a pole, tube, bench or table. Its jaws will attach to anything between 12 to 55mm in width.It can be fixed either vertically or horizontally. The camera attaches to the ball levelling head making it ideal for all types of handheld camera up to 1.5kg.

Hague Car Camera Suction Mount With Double Ball Tilt Head

Hague SM1 (SM-1, SM/1, SM_1, SM 1) Car Camera Suction Mount With Double Ball Tilt Head The Hague SM1 Car Camera Suction Mount can be attached to any non-porous surface, which makes it ideal for mounting the camera onto a vehicle whether inside or out. It can be fixed either vertically or horizontally. The camera fastens to a reversible camera plate, which enables the camera to be mounted above or below the suction mount. This makes it ideal for use on a car windscreen, the camera can be positioned to look through the windscreen or into the vehicle. A fully adjustable double ball bracket has a single lever for locking the camera into the required position. It's ideal for all types of handheld cameras up to 1.5kg.

Hague Dual Shoulder Supports With Rod Clamp

Hague DSS (DS-S, DS/S, DS_S, DS S) Dual Shoulder Supports With Rod Clamp The Hague Dual Shoulder Supports rest on both shoulders to give the camera much more stability than rigs that just rest on one shoulder. When all the rigs weight is in front of the shoulders it is much more effective to have it rested across the two shoulders and this helps with both stability and weight distribution. However if the operator prefers the rig to rest on one shoulder the shoulder supports can be adjusted for single shoulder operation. The clamp on the shoulder supports secures it to the two rods and allows it to be used with the Hague DSR Dual Shoulder Support or other systems that are using the standard 15mm x 60mm pitch rod system.

Hague Dual Shoulder Camera Support Rig

Hague DSR (DS-R, DS/R, DS_R, DS R) Dual Shoulder Camera Support Rig The Hague Dual Shoulder Camera Support Rig is an ideal rig for both camcorders and DSLRs. It is based on the standard 15mm x 60mm pitch rod system, so it can be used in conjunction with other manufacturer’s components, such as follow focus systems, or parts of the Hague support can be added to other manufacturer’s rigs. The dual shoulder camera support rig can be purchased as a complete rig or as individual parts. The dual shoulder support rests on both shoulders to give the camera much more stability than rigs that just rest on one shoulder. As all the rigs weight is in front of the shoulders, having it resting on both shoulders is much more effective, however if the operator prefers the rig to rest on a one shoulder the rig can be adjusted for single shoulder operation. The clamp on the support secures it to the two rods. The quick-release camera plate makes it easy to get your camera on and off the rig and is compatible with most popular Manfrotto video heads. The clamp on the camera plate secures it to the rods with easy adjustment forward or back to get the camera into the required position. The twin handgrip is used to support the rig, both handles can be used to support the rig or a single handle can be set in the centre of the clamp for single-hand operation, leaving your other hand free to control the camera and focusing. The clamp on the handgrips secures it to the rods. The two support rods connect all the parts together. If the rig is purchased as a complete unit it will be supplied with 300mm long support rods. Other lengths are available as optional extras. The whole rig is made from lightweight aluminium with black powder coating on the shoulder supports. All the parts are compatible with the majority of rigs on the market using 15mm rods on a pitch of 60mm.

Hague Twin Head Tripod Mount 75mm Bowls

Hague THM75 (TH M75, TH-M75, TH/M75, thm75) Twin Head Tripod Mount 75mm Bowls The Hague THM75 Twin Head Camera Mount enables two video heads to be mounted to one tripod, making it ideal for a two camera shoot where space is limited. One operator can use one camera for a “wide shot” while using the main camera to follow the action. With both cameras being so close together the operator can use the flip-out screens on the cameras to monitor both shots. This makes it ideal for stage shows, conferences, weddings etc. The mount will attach to any pro tripod with a 100mm or 75mm bowl. It has a 75mm bowl at either end making it easy to level off the video heads. The video head from the tripod can be used at one end of the mount and a second head can be mounted to the other end, which we can supply if required.  

Hague 100mm Bowl Mount With Superclamps

Hague BMS (BM-S, BM/S, BM_S, BM S) 100mm Bowl Mount With Superclamps The Hague 100mm Bowl Mount with Superclamps can attach to a horizontal pole, roll bar, scaffolding, ladder run, table edge or something similar. It is held in position by two superclamps, the jaws of the clamps will attach to a pipe/tube between 12 to 55mm in diameter or to a table/beam with a maximum width of 25mm. The 100mm. bowl gives a rigid platform onto which you can attach your video head, (an optional stepper ring is available if you are on the 75mm. levelling system and we can also supply video heads if required). It's ideal for use in locations where it is impossible to use a tripod, such as ladders or step ladders to get that high shot or on railings or scaffolding.

Hague Low Hat 100mm Bowl

Hague LH100 (LH 100, LH-100, LH/100, lh100) Low Hat 100mm Bowl The Hague 100mm Low Hat enables you to get very low shots using your existing video head from your tripod. The bowl mount accepts most heads using the popular 100mm levelling system, should your head have the 75mm system an optional 100 to 75 stepper ring is available. Also supplied with the mount is a handwheel and collar to replace the long handle on Manfrotto heads.   The Hague Low Hat has a 3/8” threaded hole in the centre of its base, making it easy to attach to a camera slider or to a telescopic column of a compatible tripod. It also has three evenly spaced mounting holes to secure it to a step ladder, apple-box, dolly or a sheet of wood.  

Hague Wall/Ceiling Mount with Magic Arm

Hague WB3 (WB-3, WB/3, WB_3, WB 3) Wall/Ceiling Mount with Magic Arm The Hague WB3 wall/ceiling mount can be screwed to a ceiling, wall or table. The magic arm extends up to 53cm away from the fixing point and is fully adjustable in all directions, with a single handwheel for locking it in position. The reversible camera plate enables the camera to be mounted above or below the arm.   

Hague SC3 Superclamp with Magic Arm

Hague SC3 (SC 3, SC-3, SC/3, sc3) Superclamp with Magic Arm  

Hague Telescopic Suction Mount

Hague Telescopic Camera Suction Mount For Cars 

Hague Double Suction Mount

Hague Double Suction Mount  The Hague SM4 Double Suction Mount for cars has two strong suction pads which can be attached to any flat non-porous surface and these give the camera mount extra stability. It has a large camera plate which supports the camera over a greater area preventing any movement in the camera's plastic casing. A double ball bracket, along with the tubular structure, enable the camera to be mounted in a variety of positions. It’s ideal for mounting a camera either outside or inside a vehicle, or on glass windows, or any flat non-porous surface. Ideal for all handheld cameras up to 3kg. Suction pad diameter 150mm. (pump action vacuum). 

Hague Camcorder Mounting Kit

Hague CMK (CM-K, CM/K, CM_K, CM K) Camcorder Mounting Kit The Hague CMK camera mounting kit for cars has been specifically designed by Hague for mounting a lightweight camera onto a vehicle, whether inside or out. It is ideal for use on the windscreen or back window! The Camera Suction Mount can be attached to any non-porous surface, which makes it ideal for mounting the camera onto a vehicle whether inside or out. It can be fixed either vertically or horizontally. The camera fastens to a reversible camera plate, which enables the camera to be mounted above or below the suction mount. This makes it ideal for use on a car windscreen, the camera can be positioned to look through the windscreen or into the vehicle. A fully adjustable double ball bracket has a single lever for locking the camera into the required position. It's ideal for all types of handheld cameras up to 1.5kg. The mounting kit enables you use a superclamp instead of the suction pad to attach the camera to a roll-bar, roof rail etc. it attaches to anything between 12 & 55mm. in diameter.

Hague Pro Steadymount

Hague Pro Steadymount