Hague Sbag Soft Padded Bag

Hague Sbag Soft Padded Bag(HAG-SBAG) Soft padded transit bag with carrying straps suitable for the D5 Tripod Tracking Dolly, K14 Pro Jib, K16DV Camcrane. Bag colour is Navy Blue.

Hague D5T Camera Tripod Tracking Dolly Kit

Hague D5T Camera Tripod Tracking Dolly Kit(HAG-D5T) The Hague D5T Tripod Tracking Dolly Kit is a quick and easy to use system that has been designed to create super smooth tracking shots with your own tripod. The dolly has two sets of locating holes for the tripod legs which means the tripod can be used in both high and low positions. It has eight radial ball bearing wheels which set the track width to the correct positions as the dolly moves down the track. As a result the track does not require additional supports going between the two sides of track which makes it quicker to set-up and also allows the dolly to pull the track into place which makes it run smoother. The D5T Tripod Tracking Dolly is ideal for use on location or in the studio, all you need is a reasonably flat surface. The dollies width has been set to allow it to go through the majority of doorways and it has its own levelling system which prevents any rocking should the track be on slightly uneven ground. It runs on 40mm diameter track and is supplied with eight 1.5m lengths which provides a 6m run. The dolly will accept all tripods that have feet smaller than 45mm in diameter or with a base spreader and 3 straps are supplied for securing your tripod to the dolly.

Hague TRIPOD POLE BRACKET

Hague TRIPOD POLE BRACKET TP B TPB TP-B TP/B The Hague Tripod Pole Bracket enables you to attach a pole or mast to your tripod for aerial photography or video. The bracket attaches to most sturdy tripods, as long as the tripod head can be removed leaving the 3/8 threaded stud, as it is this stud that the bracket fastens to. Once attached, the tripod can be levelled off by using the spirit level on the bracket. Any pole/mast can be attached with a diameter between 35 and 51mm and it is compatible with all Hague Highshot handheld camera poles. The tripod bracket holds your pole/mast to the tripod. The mast can then hold your camera in an elevated position for sports events, property photography or site surveys. It's also ideal when using Virtual Reality 360 degrees cameras.

Hague SUCTION PAD WITH 5/8" STUD

Hague SUCTION PAD WITH 5/8" STUD SM 58 SM58 SM-58 SM/58 The Hague SM58 Suction Pad has a standard 5/8” (16mm) stud attachment coming from the pad and can be attached to any non-porous surface.

HAGUE CAMSLIDE MICRO 2

HAGUE CAMSLIDE MICRO 2 MICRO 2 MICRO2 MICRO-2 MICRO/2  The Hague Camslide Micro 2 Camera Slider is a compact system which allows you to quickly capture great tracking shots. Suitable for cameras up to 1kg the Hague Micro 2 Camslide has an adjustable ball head for mounting the camera and setting the position of the shot.  The small and lightweight rail makes this system very compact and easy for transport. At each end of the rail are end supports with mini rubber feet for use on table tops or the floor and in the centre of the rail is a standard 1/4” threaded hole for tripod mounting.  With slider shots often only requiring a small amount of movement to create a stunning shot, the 500mm rail allows the user to capture great shots from such a compact system. The smooth rail combined with the low profile ball head makes the Micro 2 a great addition to a filmmakers kit. Creating smooth movements with the Camslide Micro 2 is easy to achieve as the unique carriage design incorporates an indent to which you can use your finger or thumb to control the movement. This makes it easy to control the movement and create those stunning tracking shots.   Suitable for balanced camera set-ups that weigh up to 1kg in weight and cameras should be mounted so they are centrally balanced for optimum performance. Ideal lightweight cameras.

Hague TRACK KIT - IDEAL FOR D10 DOLLY

Hague TRACK KIT - IDEAL FOR D10 DOLLY T K TK T-K T/K The Hague TK Track Kit is designed for the Hague Skater Ladder Dolly and enables you to get tracking shots over any terrain. It can be placed at ground level or raised for higher shots. When used in a higher position the track must be supported at both ends and can be supported in a variety of different ways. You could use a tripod at one end and then another item (such as a box, crate or table) at the other end, you could mount it between two items (such as chairs) or you could suspended it across two tripods. When used on the ground the adjustable feet on the support brackets enable you “level off” the track. The 1.8 metre track kit breaks down into separate pieces for easy transit.    

Hague MICRO CAMERA DOLLY

Hague MICRO CAMERA DOLLY M CD MCD M-CD M/CD The Hague Micro Camera Dolly enables you to create tracking shots on a table or any smooth surface. The wheel axels are adjustable, so the dolly will either track in a straight line or the wheels can be set to track around an object. The 30mm diameter wheels have rubber tyres which make the dolly quiet to move.   The Micro Camera Dolly can have cameras attached directly to it or you could use a ball head (optional extra) with the device. It is ideal for small cameras like the GoPro or for lightweight video cameras.

Hague STAND DOLLY

Hague STAND DOLLY D 1 D1 D-1 D/1 The Hague D1 Stand Dolly has been designed for use with the Hague K2WS Junior Jib With Stand and K10 Camcrane jibs as well as the PHS Power Head Stand and the TVS LCD/Monitor Stand with Vesa tilt mount. This sturdy dolly has large 100mm diameter, individually braked, swivel wheels enabling the dolly to be moved with ease. It's made of aluminium and folds down for easy transportation. It is quick and simple to set up and is supplied with 3 straps to secure the stand to the dolly. Colour black. Suitable for Hague K2WS Junior Jib With Stand, K2S Junior Jib Stand, K10 Camcrane, TVS LCD/Monitor Stand With Vesa Tilt Mount, PHS Power Head Stand.    

Hague COMPACT PRO JIB - 75MM BOWL

COMPACT PRO JIB - 75MM BOWL K 5 K5 K-5 K/5 The Hague Compact Pro Jib is a traditional camera jib which is compact, lightweight and easy to transport. It utilises the video head and the legs of your own tripod and you can operate the jib from either end. At the camera end you will be able to both pan and tilt, crane up and down and pan the jib from side to side. It’s ideal for both camcorders and DSLRs cameras weighing less than 3kg (6.6lbs). This low cost system gives you great control over your shots and allows you to create really smooth professional crane and panning movement. This Hague compact camera jib has been designed for use with tripod’s that use the 75mm “bowl type” levelling system. The video head is simply removed from the tripod legs and the jib is then attached and secured through the bowl on the tripod, the head then fastens to the levelling bowl on the end of the jib. The jib is supplied in two parts and is very quick and simple to set up.  The jib’s telescopic counterbalancing arm uses standard bar weights, or a sandbag, for counterbalance (not supplied). Once balanced the jib has an effortlessly smooth vertical crane movement that will lift your camera from ground level to 2 metres (79”) high. On the side of the jib there are several mounting points for a monitor, or any other accessories, to be attached. A pan lock and a jib lock will hold the jib in a set position when required.   The Hague Compact Pro Jib can be used on any 75mm "Bowl type" tripod, or on a 60 or 65mm "Bowl type" tripod but the optional stepper ring (SR75) would be required to attach the tripod head to the jibs bowl. On a sturdy tripod the jib will support a maximum weight of 8kg (17.6lbs) including video head and camera. 

Hague COMPACT PRO JIB - 75MM BOWL

COMPACT PRO JIB - 75MM BOWL K 5 K5 K-5 K/5 The Hague Compact Pro Jib is a traditional camera jib which is compact, lightweight and easy to transport. It utilises the video head and the legs of your own tripod and you can operate the jib from either end. At the camera end you will be able to both pan and tilt, crane up and down and pan the jib from side to side. It’s ideal for both camcorders and DSLRs cameras weighing less than 3kg (6.6lbs). This low cost system gives you great control over your shots and allows you to create really smooth professional crane and panning movement. This Hague compact camera jib has been designed for use with tripod’s that use the 75mm “bowl type” levelling system. The video head is simply removed from the tripod legs and the jib is then attached and secured through the bowl on the tripod, the head then fastens to the levelling bowl on the end of the jib. The jib is supplied in two parts and is very quick and simple to set up.  The jib’s telescopic counterbalancing arm uses standard bar weights, or a sandbag, for counterbalance (not supplied). Once balanced the jib has an effortlessly smooth vertical crane movement that will lift your camera from ground level to 2 metres (79”) high. On the side of the jib there are several mounting points for a monitor, or any other accessories, to be attached. A pan lock and a jib lock will hold the jib in a set position when required.   The Hague Compact Pro Jib can be used on any 75mm "Bowl type" tripod, or on a 60 or 65mm "Bowl type" tripod but the optional stepper ring (SR75) would be required to attach the tripod head to the jibs bowl. On a sturdy tripod the jib will support a maximum weight of 8kg (17.6lbs) including video head and camera. 

Hague Long Articulating Arm Kit With Nano Clamp

Hague LAAKIT (LAA_KIT, laa_kit, laa-kit, laa/kit) Long Articulating Arm Kit With Nano Clamp The Hague Articulating Arm is ideal when used with the Nano Clamp or the Hot Shoe Adaptor to mount a monitor, sound recorder or other accessory to a tripod leg or the shoe of the camera. If the Arm is attached to the Nano Clamp it can be used to fasten a small camera to cycle, pole, table edge, etc. The Arm will support up to 1kg. It has 1/4-20 studs on both ends. All pivot points are locked by a single handwheel.

Hague HD90 Heavy Duty 90° Right Angle Tripod Camera Mount

Hague HD90 (hd-90, HD_90, HD-90, hd_90) Heavy Duty 90° Right Angle Tripod Camera Mount The Hague Heavy Duty 90° Right Angle Tripod Camera Mount has been designed for people looking to shoot in portrait mode and is suitable for a wide variety of camera set-ups. It allows you to mount the camera at a 90 degrees angle on your own tripod and is ideal for portrait filming.  The bracket has a variety of threaded holes to mount it to the tripod’s camera plate in various positions, 13 x ¼” and 17 x 3/8”. The camera can be mounted to the angle plate using either mounting holes or the slots; there are 7 x ¼” holes, 3 x 3/8” and 2 slots. The bracket is supplied with 2 x ¼” camera screws and 2 x 3/8” camera screws.

Hague LEV Levitator Stabilizer

Hague LEV (L-E-V, l/e/v, L_E_V, lev) Levitator Stabilizer The Hague Levitator is a camera support system similar to a Camframe or Fig Rig, but which has the stabilizing effect of a Steadicam. Like the Fig Rig the support is held by both hands, but the Levitator’s handles are totally free moving and the camera is self balancing, similar to a Steadicam but without the need for counterbalance weights. It’s this combination that gives the camera a levitating effect as if it is floating through the air. The Levitator uses the camera’s own weight for counterbalance, so there is no need for counterbalance weights as used on most “Steadicam type” stabilizers. This reduces the weight of the support and the twin handle design makes it easier to hold for long periods. Once the camera is balanced, the Levitator gives the camera a truly floating effect with easy directional and tilt control with the two handles. As there is very little restriction above or below the camera, the Levitator can simply skim over or under items creating shots unattainable from other devices. The sealed radial bearings in the pivot cups and the ball socket handles reduce hand movement as you move around. It’s quick and simple to set up and the quick release camera plate makes it easy to get your camera on and off the support. Extra mounting holes and a cold shoe enables you to attach any extra accessories to the Levitator. The supplied rigging stands make it easy to adjust the Levitator’s fine trim controls until optimum balance is achieved. Also included is a Balance Correction Adapter, this is only required when heavy lenses are mounted to the camera making it very front heavy, or accessories are mounted to the camera that may affect the cameras centre of balance.  

Hague HP1 Highshot Camera Pole 6M

Hague HP1 (HP_1, hp-1, hp_1, hp/1) Highshot Camera Pole 6M The Hague 6m Highshot Camera Pole is made from lightweight glass fibre and allows you to quickly capture elevated photos or video footage. The HP1 Highshot pole is constructed from high quality composite materials and is finished with an acrylic resin making it an economical and portable solution which supports up to 2kg. The Hague telescopic Highshot poles are a great way to quickly achieve height and are ideal for property photography, site surveys or sports filming. The system is supplied with a tilt head attached to the top which allows you to angle the camera position and you can then rotate the whole pole. The tilt head incorporates a quick release camera plate, with a standard ¼” camera screw attachment, and this makes it easy to quickly add or remove the camera. The telescopic Highshot pole is supplied with a high quality footplate which allows for smooth rotation of the pole when elevated and this folds up neatly for transport. This helps with the stability and usability of the pole. Optional extras, listed below, include clamps and brackets which allow the user to mount viewing monitors, tablets or phones to the pole so you can easily see what you are capturing or to control the camera functionalities. Comprising of four sections the HP1 extends to 6m yet reduces down to 1.75cm for transit and is supplied in a padded transit bag.

Hague AMP4 Highshot Camera Mast With Manual Pan & Tilt

Hague AMP4 (A_M_P4, amp4, amp_4, amp/4) Highshot Camera Mast With Manual Pan & Tilt The Hague Highshot Camera Mast with manual pan & tilt capability is ideal for both photography and filming applications, including property photography, sports filming and sports analysis. Supplied in a padded transit bag for easy transportation. Hague Camera Supports have been a leading solutions expert in Aerial Mast Photography and Filming for many years, supplying kits into universities, professional sport teams, estate agencies and sport analysis companies around the world. The new range of Hague Highshot kits are an extension to the current range and offer the flexibility and performance required for professional use. The 6.2m (20ft 4”) Hague Highshot Mast provides an elevated view, with the ability to manually pan and tilt the camera. It’s ideal for compact cameras and small camcorders. Most modern cameras now have WiFi and Bluetooth capability so the camera can be controlled by an app on your phone or tablet which can be mounted at the base of the mast, or a cable can be run down the mast for monitoring and camera control. The Highshot mast is supplied with cable cleats should you be running cables down from the camera. The telescopic mast is lightweight and quick to set up, it has a minimum height of 158cm and a maximum height of 620cm. It is supplied with a tilt head which has a quick release camera plate, making it easy to mount the camera. At the base of the mast a handle is attached to pan the mast with a control cable to tilt the camera. Next to the pan bar there is a mounting plate with both 1/4” and 3/8” threaded holes for attaching an articulating arm, plus a 5/8” (16mm) socket which is used to attach the supplied Hague Ball Levelling Head. The ball levelling head has a standard 1/4" camera screw on top which allows you to mount a viewing monitor directly or a phone/tablet when used with a relevant phone/tablet mount. Supplied in a padded transit bag. Applications   Indoor or outdoor, the mast gives you that extra height compared to a traditional tripod that may not be high enough. Compared with the traditional view the result is completely different and the image is greatly improved when taken from a higher view point.

Hague AMP1 Mast W/ Remote Control Head

Hague AMP1 (A_M_P1, amp1, amp_1, amp/1) Mast W/ Remote Control Head The Hague AMP1 Highshot Camera Mast with 340° powerhead allows you to reach 7.3m (24ft) in height and then control the camera position via the remote controlled powerhead. This mast kit is an ideal solution for aerial mast photography, sports analysis, site surveys and sports filming. Made from lightweight aluminium this mast is extremely portable, quick to set-up and easy to use. With its own tripod style base, which remains attached at all times and just folds up for transport, the mast provides a rigid base and each section of the mast can be raised easily by hand. Supplied in a padded transit bag. At the top of the mast there is a standard 1/4” screw attachment to which you attach the Hague Powerhead and then the supplied tilt correction plate allows you to achieve a greater tilt angle.  Once the camera is attached you can then use the supplied remote control and extension cable to control the direction/positioning of the camera whilst using a tablet or viewing monitor to see your images. Operating from a higher view point drastically changes the picture you can capture and these masts can be utilised outdoors or indoors depending upon the application they are needed for. The mast now has three adjustable legs for levelling off, a supplied spirit level and there is an attachment at the top to secure guide ropes if required. This AMP1 kit includes the Hague AMP Highshot Camera Mast supplied in a padded transit bag, the Hague 340° Powerhead with remote control and extension cable, and the Hague Tilt Correction Plate. Please note additional items, such as the iPad, SC4 Superclamp with Articulating Arm, Camera and the UTM Universal Tablet Mount, are not included and are only shown for illustrative purposes

Hague AMP Highshot Mast - 7.3M

Hague AMP (A_M_P, amp, a_m_p, a/mp) Highshot Mast - 7.3M The Hague AMP Highshot Camera Mast is a lightweight system that extends to a height of 7.3m (24ft) and is ideal for a variety of applications including aerial mast photography, sports analysis, site surveys and sports filming. Supplied in a padded transit bag. Made from lightweight aluminium this mast is extremely portable, quick to set-up and easy to use. With its own tripod style base, which remains attached at all times and just folds up for transport, the mast provides a rigid base and each section of the mast can be raised easily by hand. At the top of the mast there is a standard 1/4” screw attachment to which you would usually attach a ball head, tilt head or powerhead so the camera can then be positioned to the desired angle. Once the camera is in position you can then use a tablet or viewing monitor to see and control your images. Operating from a higher view point drastically changes the picture you can capture and these masts can be utilised outdoors or indoors depending upon the application they are needed for. The mast now has three adjustable legs for levelling off, a supplied spirit level and there is an attachment at the top to secure guide ropes if required. With this mast, you can build your own bespoke solution utilising the related products below or just use the mast by itself. Take your filming/photography capability to new heights with the AMP Camera Mast from the UK’s leading solutions expert. This AMP kit includes the Hague AMP Highshot Camera Mast supplied in a padded transit bag.

Hague DRIVE Camslide Drive Carbon Fibre Camera Slider With Auto Pan System

Hague DRIVE Camslide Drive Carbon Fibre Camera Slider With Auto Pan System The Hague Camslide Drive carbon fibre camera slider will automatically pan the camera whilst you concentrate on the sliding. This ingenious design makes it so much easier to pan and slide at the same time as you only have to concentrate on the one movement. Made from lightweight carbon fibre the Hague Camslide Drive has a smooth design and provides a smooth slider movement too. Measuring 80cm in legth it is an ideal length for working with but also a good size for travelling with. Supplied with its own transit bag the Camslide Drive is an ideal camera slider for many situations. So what’s so special about the Camslide Drive? Well it’s the peculiar looking bar down the centre that makes all the difference. This is the unique drive capability which allows the user to set the slider so it auto pans the camera as you slide along the rail. With a variety of adjustment, you can create both small movements or wide ranging pans as the camera moves along. To operate the Drive system simply adjust the angle of the centre rail and then, as the carriage moves along the rail, it will automatically pan the direction of you camera on the ball head or video head. Please note we would not recommend trying to tilt the camera at the same time as using the auto pan mode but you can set the ball head or video head at a tilted angle. The carriage has a larger seating area which makes it ideal for mounting ball heads or video heads and it incorporates 4 roller bearings for a smooth slider movement. The carriage has a 1/4" screw and a 3/8” adaptor which makes it ideal for mounting ball heads and video heads. There is also a spirit level included within the carriage. The rail is made from lightweight carbon fibre rods and the 80cm length is a very good working length but is not too big for transit. The new style end supports are supplied with adjustable feet which fold up to make the slider compact for travelling and can be used at different angles when on slightly uneven ground. The slider has a mounting plate which allows it to be mounted onto a tripod via both the 1/4” and 3/8” camera screws.   Supplied with its own travel bag the Hague Camslide Drive carbon fibre slider is a lightweight system which is ideal for professional camera set-ups that weigh less than 8kg.

Hague EDGE Camslide Edge Carbon Fibre Camera Slider

Hague EDGE Camslide Edge Carbon Fibre Camera Slider The Hague Camslide Edge camera slider is made from lightweight carbon fibre and provides a smooth sliding movement for professional tracking shots. Measuring 80cm in length the Camslide Edge offers a very workable length and can be used on the ground, a table or tripod mounted. The Camslide Edge has a heavy duty carriage which incorporates 6 roller bearings to ensure a smooth movement with little play and there is a breaking system that can be used to add drag or to lock off the carriage. The larger seating area of the carriage is ideal for getting cameras better balanced on ball heads and video heads. The carriage has a 1/4" screw and a 3/8” adaptor which makes it ideal for mounting ball heads and video heads. There is also a spirit level included within the carriage. The rail is made from lightweight carbon fibre rods and the 80cm length is a very good working length but is not too big for transit. The new style end supports are supplied with adjustable feet which fold up to make the slider compact for travelling and can be used at different angles when on slightly uneven ground. The slider has a mounting plate which allows it to be mounted onto a tripod via both the 1/4” and 3/8” camera screws.   Supplied with its own travel bag the Hague Camslide Edge is a lightweight camera slider which is ideal for professional camera set-ups that weigh less than 8kg.

Hague S600 Camslide Camera Slider

Hague S600 Camslide Camera Slider The Hague S600 Camslide is a high quality camera slider designed to offer a low cost solution for smooth slider shots. It is an ideal solution for camera set-ups that weigh up to 4kg (8.8lbs). The S600 Camslide has a lightweight aluminium rail, high quality roller bearings, adjustable end supports and is supplied in a padded transit bag.  Hague Camera Supports were one of the first companies to ever design a camera slider and the new Camslide S600 honours that history with a traditional style rail, combined with modern day enhancements in performance.   The Hague Camslide has been re-designed to offer unparalleled performance in such a low cost solution. With the introduction of adjustable end supports and high quality roller bearings the S600 allows you to create smooth slider shots from a compact and lightweight system. The new carriage has been carefully constructed with the introduction of the high quality roller bearings, a carriage lock and a spirit level. There is a standard 3/8" screw, to which you attach either a ball head or a video head, and the camera can then be positioned to the desired angle for your shot. At each end the adjustable end supports allow the slider to be levelled across a variety of terrains and these fold up neatly for transit, or when used on a tripod.   The rail itself has standard 1/4" and 3/8" threaded holes in the centre so it can be attached to a single tripod but it also has additional 1/4" and 3/8" holes at both ends should there be a requirement to mount it across two tripods. Within the end supports, and the carriage, there are also additional threaded holes to which accessories could be attached.

Hague BMS75 Bowl Mount 75mm with Superclamps

Hague BMS75 (BM-75, BM/75, bm75) Bowl Mount 75mm with SuperclampsThe Hague 75mm bowl mount gives a rigid platform onto which you can attach your video head.Suitable for 75mm bowl type tripod heads the BM75 Bowl Mount has two 5/8" spigots on the bottom which allows it the be attached to items with a 5/8" socket, such as a Superclamp.Colour - Black.Supports up to 16kg.

Hague Ceiling Mount With Double Ball Bracket

Hague WB2 (WB-2, WB/2, WB_2, WB 2) Ceiling Mount With Double Ball Bracket The Hague WB2 wall/ceiling mount with a double ball tilt head can be screwed to a ceiling, wall, or table. The double ball bracket is fully adjustable with a single lever for locking. A reversible camera plate enables the camera to be mounted above or below the fixing point.

Hague Superclamp With Double Ball Tilt Head

Hague SC2 (SC-2, SC/2, sc2) Superclamp With Double Ball Tilt Head The Hague SC2 Superclamp with Double Ball Tilt Head is ideal for mounting a camera onto a vehicle, rod or post as it is fully adjustable and can be mounted either horizontally or vertically. On cars it can be fastened to a rollbar, roof rails or a roof rack. The Superclamp & Double Ball Tilt Head can be attached to a pole, tube, bench or table. Its jaws will attach to anything between 12 to 55mm in width. It can be fixed either vertically or horizontally. The Double Ball Tilt Head with a reversible camera plate can be set at any angle or direction with a single lever for locking. It's ideal for all types of cameras up to 3kg.

Hague SC1 Superclamp With Ball Levelling Head For Cameras

Hague SC1 (SC-1, SC/1, sc1) Superclamp With Ball Levelling Head For CamerasThe Hague SC1 Superclamp with Ball Leveller can be used to secure the camera to a pole, tube, bench or table. Its jaws will attach to anything between 12 to 55mm in width.It can be fixed either vertically or horizontally. The camera attaches to the ball levelling head making it ideal for all types of handheld camera up to 1.5kg.

Hague PHEC20 Powerhead Extension Cable 20m

Hague PHEC20 (PHEC-20, PHEC/20, PHEC_20, PHEC 20, phec20) Powerhead Extension Cable 20m Hague PHEC20 Power Head Extension Cable 20m (65ft) extension cable for the Hague Power Heads. Suitable for the Hague PH / MPH / UPH / PH100 (Version 2 November 2019) models. 

Hague Powerhead Stand

Hague PHS (PH-S, PH/S, PH_S, PH S) Powerhead Stand The Hague PHS Power Head Stand is an ideal solution for mounting the Hague PH and MPH powerheads. The Pan and Tilt Power Head fastens directly onto the sturdy stand and it has an adjustable telescopic column with a minimum height of 110cm and a maximum height of 188cm. The column can be locked at the required height and there is a safety pin to prevent the column slipping. It is ideal for stage shows, conferences, and weddings. The stand is made from lightweight aluminium.

Hague Car Camera Suction Mount With Double Ball Tilt Head

Hague SM1 (SM-1, SM/1, SM_1, SM 1) Car Camera Suction Mount With Double Ball Tilt Head The Hague SM1 Car Camera Suction Mount can be attached to any non-porous surface, which makes it ideal for mounting the camera onto a vehicle whether inside or out. It can be fixed either vertically or horizontally. The camera fastens to a reversible camera plate, which enables the camera to be mounted above or below the suction mount. This makes it ideal for use on a car windscreen, the camera can be positioned to look through the windscreen or into the vehicle. A fully adjustable double ball bracket has a single lever for locking the camera into the required position. It's ideal for all types of handheld cameras up to 1.5kg.

Hague Dual Shoulder Supports With Rod Clamp

Hague DSS (DS-S, DS/S, DS_S, DS S) Dual Shoulder Supports With Rod Clamp The Hague Dual Shoulder Supports rest on both shoulders to give the camera much more stability than rigs that just rest on one shoulder. When all the rigs weight is in front of the shoulders it is much more effective to have it rested across the two shoulders and this helps with both stability and weight distribution. However if the operator prefers the rig to rest on one shoulder the shoulder supports can be adjusted for single shoulder operation. The clamp on the shoulder supports secures it to the two rods and allows it to be used with the Hague DSR Dual Shoulder Support or other systems that are using the standard 15mm x 60mm pitch rod system.

Hague Dual Shoulder Camera Support Rig

Hague DSR (DS-R, DS/R, DS_R, DS R) Dual Shoulder Camera Support Rig The Hague Dual Shoulder Camera Support Rig is an ideal rig for both camcorders and DSLRs. It is based on the standard 15mm x 60mm pitch rod system, so it can be used in conjunction with other manufacturer’s components, such as follow focus systems, or parts of the Hague support can be added to other manufacturer’s rigs. The dual shoulder camera support rig can be purchased as a complete rig or as individual parts. The dual shoulder support rests on both shoulders to give the camera much more stability than rigs that just rest on one shoulder. As all the rigs weight is in front of the shoulders, having it resting on both shoulders is much more effective, however if the operator prefers the rig to rest on a one shoulder the rig can be adjusted for single shoulder operation. The clamp on the support secures it to the two rods. The quick-release camera plate makes it easy to get your camera on and off the rig and is compatible with most popular Manfrotto video heads. The clamp on the camera plate secures it to the rods with easy adjustment forward or back to get the camera into the required position. The twin handgrip is used to support the rig, both handles can be used to support the rig or a single handle can be set in the centre of the clamp for single-hand operation, leaving your other hand free to control the camera and focusing. The clamp on the handgrips secures it to the rods. The two support rods connect all the parts together. If the rig is purchased as a complete unit it will be supplied with 300mm long support rods. Other lengths are available as optional extras. The whole rig is made from lightweight aluminium with black powder coating on the shoulder supports. All the parts are compatible with the majority of rigs on the market using 15mm rods on a pitch of 60mm.

Hague Track Extension Kit

Hague TKE (TK-E, TK/E, TK_E, TK E) Track Extension Kit The Hague TKE Track Kit Extension is designed to extend the Hague TK Track Kit. It consists of two additional pieces of track and a mid rail support. These are then used in conjunction with the standard track kit to extend the length by 900mm. The standard track kit end supports are used at each end and the additional extension bars are used in the centre with the rail support. The Hague TK Track Kit is designed for the Hague Skater Ladder Dolly and enables you to get tracking shots over any terrain.

Hague Ladder Supports - Ideal For D10 Dolly

Hague LS (L-S, L/S, L_S, L S) Ladder Supports - Ideal For D10 Dolly Set of two Ladder Supports for the Hague Skater Ladder Dolly D10. The Hague ladder supports are used at each end of the ladder for extra stability. Each support has two adjustable feet which enable the ladder to be “levelled off “when used on uneven ground. These supports can also be used to mount the ladder across two tripods, the supports are secured to the tripods with the supplied mounting studs and handwheels. Alternatively an optional Claw Ball could be used to secure the supports to the tripod. When mounted across two tripods, tracking shots can be achieved over any terrain, without the need for laying tracks on the ground.

Hague Junior Jib Stand

Hague K2S (K2-S, K2/S, K2_S, K2 S) Junior Jib Stand The Hague Junior Jib Stand is ideal if you do not have a suitable sturdy tripod to mount the jib on. It has an adjustable telescopic column with a minimum height of 110cm and a maximum height of 188cm. The column can be locked at the required height and there is a safety pin to prevent the column slipping.  The stand is made from lightweight aluminium.

Hague Tripod Extender 100mm System

Hague TE100 (TE-100, TE/100, TE_100, TE 100) Tripod Extender 100mm System The Hague 100mm Tripod Extender raises the height of your tripod by almost ½ a metre. This makes it ideal for those situations when you would like to get a bit more height on your tripod, such as when you want to get a shot over the top of people who are standing or in any awkward locations where a bit more height would create a much better shot. The Tripod Extender has been designed for use with pro tripods that use the bowl levelling system. There are two versions the Tripod Extender, TE75 for tripods with a 75mm levelling system or TE100 for a 100mm levelling system.The Hague Tripod Extender is quick and simple to attach, you simply remove your head from the tripod and mount the extender in it’s place. The video head is then attached to the bowl on top of the extender in the same way as it was fastened to your tripod. The video head can then be levelled off in the usual way.

Hague Tripod Extender 75mm System

Hague TE75 (TE-75, TE/75, TE_75, TE 75) Tripod Extender 75mm System The Hague 75mm Tripod Extender raises the height of your tripod by almost ½ a metre. This makes it ideal for those situations when you would like to get a bit more height on your tripod, such as when you want to get a shot over the top of people who are standing or in any awkward locations where a bit more height would create a much better shot.The Tripod Extender has been designed for use with pro tripods that use the bowl levelling system. There are two versions the Tripod Extender, TE75 for tripods with a 75mm levelling system or TE100 for a 100mm levelling system.The Hague Tripod Extender is quick and simple to attach, you simply remove your head from the tripod and mount the extender in it’s place. The video head is then attached to the bowl on top of the extender in the same way as it was fastened to your tripod. The video head can then be levelled off in the usual way.

Hague K11 Compact Camera Crane - Jib

Hague K11 (K-11, K/11, k11) Compact Camera Crane - JibThe Hague K11 Compact Camera Jib is so small & compact it can be taken almost anywhere with ease. The Camera Crane has been specifically designed to be lightweight and simple to set up, allowing you to enhance your video productions by getting those beautifully professional looking crane shots.The jib is supplied in two parts which are only 800mm (31 ½”) long. These slot together (no tools required) to create a jib that has a vertical crane movement that will lift your camera from ground level to a height of 2.6 metres (8ft 6”).It mounts directly to the tripod’s head in the same way as you would mount your camera and it can be held by both ¼” and 3/8” camera screws. The jib uses the tripod’s head for pan movement which allows the jib to smoothly pan from side to side and move round through 360 degrees. Locking the tilt on the tripod video head ensures the camera will remain level as the jib is raised up and down.It has a maximum crane movement of 2.6 metres (8ft 6”), which is far greater than other jibs in this class and price bracket. A standard bar weight or a sandbag can be used for counterbalance (not supplied). The telescopic counterbalance bar can be adjusted to get the correct balance to match your camera’s weight.The ideal camera weight is between 0.5kg to 2kg, but the jib will support up to 2.5kg when mounted to a suitable tripod or it could be mounted to the K11S - Stand which we sell as an optional extra please see below.

Hague D9 Camera Table Tracking Dolly

Hague D9 (D 9, D-9, D/9, d9) Camera Table Tracking Dolly The Hague D9 Table Dolly enables you get tracking shots on a table, board or any smooth surface. The high quality 80mm diameter wheels have twin sealed radial ball bearings, which make the table dolly easy and quiet to move. The dolly will track in a straight line or it can be set to track in an arc, to go round an item. On top of the dolly is a 75mm bowl, this enables you to transfer your “75mm bowl type” video head from your tripod onto the dolly and level it off on the bowl mount. You then have the facility to be able to both pan and tilt whilst tracking the dolly. The large footprint of the dolly prevents tipping or slipping when using the video head. It's ideal for both DSLRs and camcorders. An articulated arm, for a monitor or other accessory, can be fastened to the dolly using one of the table dollies 1/4” or 3/8” threaded mounting points. Includes D9 Table Dolly. The price does not include the video head, camera, monitor or any other accessories shown.  

Hague D10 Camera Skater Ladder Dolly

Hague D10 (D-10, D 10, D/10, d10) Camera Skater Ladder Dolly The Hague dual purpose Skater Ladder Dolly runs on any smooth, flat surface and the wheels can be set to track in a straight line or angled to track round an object.  The Hague Skater Ladder Dolly also runs on a ladder to create tracking shots over any terrain. The high quality wheels have sealed radial ball bearings to ensure super smooth movement. Your video head can easily attach to the dolly as it has a 75mm bowl mount. This means you can simply remove the head from your tripod and mount it on the dolly, with the facility to level off the head. The 75mm bowl levelling system has now become the most popular on the majority of professional tripods. When the dolly is mounted onto a ladder an extra set of guide wheels are used to prevent it from coming off the ladder and the dolly’s width is adjustable to accommodate the different widths of ladder.   A ladder makes an ideal track as it can just be laid on the ground for low shots or suspended above ground for higher shots or to go over an item. This enables you to get tracking shots over any terrain. Optional ladder supports are available to suspend the ladder between two tripods or to level off the ladder when used on the ground. A track kit is also available, with the advantage of the track breaking down to shorter lengths for easier transportation.

Hague K3 Mini Camera Jib Traveller

Hague K3 (K-3, K 3, K/3, k3) Mini Camera Jib Traveller The Hague Mini Jib Traveller K3 is small, compact, lightweight and easy to take anywhere. Measuring just 82cm for transit, and weighing just 2kg, this jib is ideal for people on the go. It’s ideal for both DSLRs and all handheld camcorders under 3kg, or could be used with action cameras such as the GoPro for an even more lightweight set-up. The Mini Jib Traveller is fastened directly to the video head of any sturdy tripod, in the same way you would attach your camera. It can be mounted using both 1/4” and 3/8” screws. On the end of the jib is a camera plate mounted on a pulley with a control cable coming down the jib to a second pulley at the side of the video head on the tripod. It is this control cable that keeps the camera level as the jib is raised or lowered. Tilting the tripod’s video head controls the camera pulley on the end of the jib, enabling the camera to be tilted up or down. The radial ball bearings in the pulley ensure a very smooth tilt movement. The jib has a telescopic weight bar which can be adjusted to counterbalance the camera with standard bar weights (not supplied) or a sandbag used for counterbalance. An additional feature of the Mini Jib Traveller is the ability to mount the jib horizontally so you can create sideways tracking movement, similar to a slider, or the camera can be positioned to move forward or back. Combine this with using the pan bar on the video head and some very unusual shots can be achieved. Specifications: Up and Down Crane movement - 140cm, Length from tripod to camera - 72cm, Telescopic weight bar length 20 - 70cm, Total maximum length 146cm, Transit Size: 82 x 10 x 7cm, Weight: 2kg.   Includes K3 Mini Jib Traveller with tilt facility. The price does not include the tripod, camera, weights or any other accessories shown.  

Hague K10-UPH Camcrane with stand & underslung powerhead

Hague K10-UPH (K10UPH, K10 UPH, K10/UPH, k10-uph) Camcrane with stand & underslung powerhead The Hague CamCrane K10-UPH is quick and simple to set up, it is supplied with its own stand and a underslung remote controlled pan & tilt powerhead. The stand's height is adjustable from 1.1 to 1.4 metres high with standard bar weights (not supplied) used for counterbalance, these are held in place by the weight bar and there is an adjustable fine trim weight to obtain perfect balance. Once balanced the camera can smoothly move from ground level to almost 4 metres high and the crane will pan 360 degrees on the stand. You also have the ability to pan and tilt the camera through 360 degrees by controlling the underslung powerhead using the wired remote control. The distance from the stand to the camera is 2.5 metres and the K10 has a total length of 3.6 metres. It is ideal for all handheld cameras under 2.5kg. An optional monitor bracket is available, this enables a LCD monitor to be fastened to the crane, making it easier to monitor your shots.   The Hague UPH electronic motorized Underslung Pan & Tilt Power Head is suitable for all handheld cameras that weigh less than 2.5kg. Having the camera underslung gives much greater tilt movement (360 degrees) which enables the camera to point directly down if required. The unit is battery operated with a wired remote control for both pan & tilt, it also has a variable speed control.  Includes: K10 CamCrane, Fine Trim Weight, Weight Bar, Remote Underslung Pan & Tilt Power Head, Power Head Remote and extension cable.

Hague K18-UPH Camera Crane Jib With Remote Controlled Powerhead

Hague K18-UPH (K18UPH, K18 UPH, K18/UPH, k18-uph) Camera Crane Jib With Remote Controlled Powerhead The Hague CamCrane K18 with UPH Underslung Pan & Tilt Power Head is quick and simple to set up, it attaches to any sturdy 100 or 75mm "bowl type" tripod or can be supplied with the optional Hague Dolly D3. It’s ideal for both handheld camcorders and DSLR cameras up to 2kg (4.4lbs) in weight.   Once balanced the camera can smoothly move from ground level to almost 7 metres high and the crane will pan 360 degrees. You have the choice of using the CamCrane at it’s full length or without two of the centre sections. At it's full length support cables are used to improve rigidity. The counterbalance arm has an adjustable fine trim weight and a weight bar with handgrips. Standard bar weights are used for counterbalance (not supplied). A supplied monitor bracket enables a LCD monitor to be fastened to the crane, making it easier to monitor your shots.   The electronic motorized Underslung Pan & Tilt Power Head is suitable for all handheld camcorders and DSLRs that weigh less than 2kg. The Power Head fastens to the crane with the supplied screws. The camera is mounted underslung with a tilt movement of 360 degrees, this enables the camera to point directly downwards when required. The head also pans 360 degrees on the end of the crane. The unit is battery operated with a wired remote control for both pan & tilt, it also has a variable speed control.   The K18 CamCrane is made of aluminium and breaks down into 5 main sections, making it easier to handle in transit. It is supplied in a cardboard carton but an optional transit case is also available.   K18 CamCrane - Specifications Length from stand/tripod to camera 427cm at its longest length, or 210cm at its shortest length. Length from stand/tripod to weight bar 143cm. Total length: 570cm or 350cm at its shortest length. Vertical crane movement from ground level to 695cm high (at its longest length) or 226cm (at its shortest length). The maximum vertical crane movement includes going down as well as up, so the crane would need to be on a raised area to achieve the full movement. Colour – Black. Transit Size: 120 x 18 x 16 cm. Weight: 17kg (37.5lbs).   UPH Remote Pan & Tilt Head - Specifications Weight – 1.7kg. (3.75lbs) Dimensions – 356x240x103mm (14x9.5x4 inches). Head sockets – 1 x 7 pin din, 1 x 6v DC in. Vertical Tilt & Horizontal Pan- 360 Degrees. Approximate speed – Pan & Tilt variable from 4 to 8 degrees per second. On/Off switch. Power Requirements – AA Batteries x 4. Head construction – Black ABS plastic and powder coated CNC machined aluminium. Maximum Camera Weight - 2kg.   UPH Hand Held Controller - Specifications Dimensions – L125 x W45 x H15mm. Control cable with 7 pin din plug. Speed - Slider control.     Price includes:- K18 CamCrane with UPH Underslung Power Head and MB/A Monitor Bracket. Price does not include the Camera, Tripod, Dolly, Monitor or any of the other accessories shown.

Hague K18-PH200 CamCrane Camera Jib With Pro Pan & Tilt Powerhead

Hague K18-PH200 (K18PH200, K18 PH200, K18/PH200, k18-ph200) CamCrane Camera Jib With Pro Pan & Tilt Powerhead The Hague CamCrane K18 with the joystick controlled PH200 Pro Pan & Tilt Power Head is quick and simple to set up, it attaches to any sturdy 100 or 75mm "bowl type" tripod or can be supplied with the optional Hague Dolly D3. It’s ideal for both handheld camcorders and DSLR cameras up to 4kg (8.8lbs) in weight.   Once balanced the camera can smoothly move from ground level to almost 7 metres high and the crane will pan 360 degrees. You have the choice of using the CamCrane at it’s full length or without two of the centre sections. At it's full length support cables are used to improve rigidity. The counterbalance arm has an adjustable fine trim weight and a weight bar with handgrips. Standard bar weights are used for counterbalance (not supplied). A supplied monitor bracket enables the PH200 control box and a LCD monitor to be fastened to the crane, making it easier to monitor your shots.   The PH200 Pro Pan & Tilt Power Head will pan and tilt through 360 degrees, this enables the camera to point directly upwards or downwards when required. It is driven by two custom-geared motors with belt drive. The power head’s drive pulleys have sealed radial ball bearings for effortless smooth movement with minimum backlash. The motor drive can be easily disengaged to enable the camera to be balanced correctly on the camera plate. The head’s camera plate is adjustable for different sizes of camera and will support up to 4kg (8.8lbs). The speed of movement is variable, from the slowest crawl up to 52 degrees per second. The drive motors are quiet at low speeds, but will be heard at higher speeds if the camera's onboard microphone is used. (Similar to most power heads on the market). The head and controller are supplied in their own transit case.   The Joystick Control gives the head precision pan and tilt movement in either direction, from a slow crawl up to the required speed. The Joystick will also pan and tilt simultaneously. On the side of the control box is a variable speed controller, so you can set the maximum speed for better control, there are also switches to change the direction of the joystick control and an on & off switch. On the front of the control box are sockets for the control cable, 12vDC in, plus a composite video out phono socket, this enables a monitor to be added to monitor your shots. Led lights indicate when the unit is switched on and when the internal battery is on charge. The head is powered by a rechargeable internal battery which will last approximately 3 hours, or can be powered from the supplied mains adaptor. On the base of the control box is a ¼” threaded hole to allow it to be mounted to the crane. A 5 metre cable is supplied to connect the control box to the head. This cable can also carry a composite signal from the head to the controller, allowing a monitor to be used without the need of additional wires.   The K18 CamCrane is made of aluminium and breaks down into 5 main sections, making it easier to handle in transit. It is supplied in a cardboard carton but an optional transit case is also available.   K18 CamCrane - Specifications Length from stand/tripod to camera 427cm at its longest length, or 210cm at its shortest length. Length from stand/tripod to weight bar 143cm. Total length: 570cm or 350cm at its shortest length. Vertical crane movement from ground level to 695cm high (at its longest length) or 226cm (at its shortest length). The maximum vertical crane movement includes going down as well as up, so the crane would need to be on a raised area to achieve the full movement. Colour – Black. Transit Size: 120 x 18 x 16 cm. Weight: 17kg (37.5lbs).   PH200 Remote Pan & Tilt Power Head - Specifications Weight – 2.4kg. Dimensions – L240 x W120 x H450mm. Head sockets – 1 x 6 pin control socket. 1 x RCA phono socket (video in). Head construction – Black powder coated CNC machined aluminium. Drive - 2 Custom-geared motors with belt driven drive pulleys. Maximum Camera Weight - 4kg. Approximate maximum sized camera L450 x W180 x H280mm.   PH200 Joystick Control Box- Specifications Weight – 1kg. Dimensions – L140 x W100 x H75mm. Control box sockets – 1 x 6 pin control socket. 1 x RCA phono socket (video out). 1 x 12vDC in socket, size 2.1mm. Switches – On/off, Pan direction, Tilt direction, and Maximum speed control. Approximate Speed – Variable from 0 to 52 degrees per second. Power Requirements – 12 -15Vdc. Control Box construction – Black powder coated aluminium with non slip feet and ¼” threaded mounting hole. Mains adapter 100-240v AC to 15Vdc. Control Cable – Length 5 metres.     Price includes:- K18 CamCrane with PH200 Pro Pan & Tilt Power Head, Control Box Mounting Bracket and Monitor Bracket. Price does not include the Camera, Tripod, Dolly, Monitor or any of the other accessories shown.

Hague Twin Head Tripod Mount 75mm Bowls

Hague THM75 (TH M75, TH-M75, TH/M75, thm75) Twin Head Tripod Mount 75mm Bowls The Hague THM75 Twin Head Camera Mount enables two video heads to be mounted to one tripod, making it ideal for a two camera shoot where space is limited. One operator can use one camera for a “wide shot” while using the main camera to follow the action. With both cameras being so close together the operator can use the flip-out screens on the cameras to monitor both shots. This makes it ideal for stage shows, conferences, weddings etc. The mount will attach to any pro tripod with a 100mm or 75mm bowl. It has a 75mm bowl at either end making it easy to level off the video heads. The video head from the tripod can be used at one end of the mount and a second head can be mounted to the other end, which we can supply if required.  

Hague 100mm Bowl Mount With Superclamps

Hague BMS (BM-S, BM/S, BM_S, BM S) 100mm Bowl Mount With Superclamps The Hague 100mm Bowl Mount with Superclamps can attach to a horizontal pole, roll bar, scaffolding, ladder run, table edge or something similar. It is held in position by two superclamps, the jaws of the clamps will attach to a pipe/tube between 12 to 55mm in diameter or to a table/beam with a maximum width of 25mm. The 100mm. bowl gives a rigid platform onto which you can attach your video head, (an optional stepper ring is available if you are on the 75mm. levelling system and we can also supply video heads if required). It's ideal for use in locations where it is impossible to use a tripod, such as ladders or step ladders to get that high shot or on railings or scaffolding.

Hague Low Hat 100mm Bowl

Hague LH100 (LH 100, LH-100, LH/100, lh100) Low Hat 100mm Bowl The Hague 100mm Low Hat enables you to get very low shots using your existing video head from your tripod. The bowl mount accepts most heads using the popular 100mm levelling system, should your head have the 75mm system an optional 100 to 75 stepper ring is available. Also supplied with the mount is a handwheel and collar to replace the long handle on Manfrotto heads.   The Hague Low Hat has a 3/8” threaded hole in the centre of its base, making it easy to attach to a camera slider or to a telescopic column of a compatible tripod. It also has three evenly spaced mounting holes to secure it to a step ladder, apple-box, dolly or a sheet of wood.  

Hague Wall/Ceiling Mount with Magic Arm

Hague WB3 (WB-3, WB/3, WB_3, WB 3) Wall/Ceiling Mount with Magic Arm The Hague WB3 wall/ceiling mount can be screwed to a ceiling, wall or table. The magic arm extends up to 53cm away from the fixing point and is fully adjustable in all directions, with a single handwheel for locking it in position. The reversible camera plate enables the camera to be mounted above or below the arm.   

Hague SC3 Superclamp with Magic Arm

Hague SC3 (SC 3, SC-3, SC/3, sc3) Superclamp with Magic Arm  

Hague Pro Pan & Tilt Power Head

Hague Pro Remote Pan & Tilt Power Head

Hague Telescopic Suction Mount

Hague Telescopic Camera Suction Mount For Cars 

Hague Suction Mounting Kit

Hague Camera Suction Mount Kit  

Hague Double Suction Mount

Hague Double Suction Mount  The Hague SM4 Double Suction Mount for cars has two strong suction pads which can be attached to any flat non-porous surface and these give the camera mount extra stability. It has a large camera plate which supports the camera over a greater area preventing any movement in the camera's plastic casing. A double ball bracket, along with the tubular structure, enable the camera to be mounted in a variety of positions. It’s ideal for mounting a camera either outside or inside a vehicle, or on glass windows, or any flat non-porous surface. Ideal for all handheld cameras up to 3kg. Suction pad diameter 150mm. (pump action vacuum). 

Hague Pro Suction Mount

Hague Pro Camera Suction Mount  The Hague SM3 Pro Suction Mount for cars has 3 suction pads which can be attached to any horizontal or vertical, non-porous flat surface. There are 3 adjustable brackets on the suction pads and 3 on the triangle plate, with a selection of connecting poles of different lengths so the mount can be used in a variety of positions. The triangle plate has a 100mm. bowl with a quick release slide plate mounted on a claw-ball leveller, making it quick and simple to set the camera to the required position. A video head could be used on the mount if required. It is ideal for mounting a camera onto a vehicle or any non-porous surface.  

Hague Camcorder Mounting Kit

Hague CMK (CM-K, CM/K, CM_K, CM K) Camcorder Mounting Kit The Hague CMK camera mounting kit for cars has been specifically designed by Hague for mounting a lightweight camera onto a vehicle, whether inside or out. It is ideal for use on the windscreen or back window! The Camera Suction Mount can be attached to any non-porous surface, which makes it ideal for mounting the camera onto a vehicle whether inside or out. It can be fixed either vertically or horizontally. The camera fastens to a reversible camera plate, which enables the camera to be mounted above or below the suction mount. This makes it ideal for use on a car windscreen, the camera can be positioned to look through the windscreen or into the vehicle. A fully adjustable double ball bracket has a single lever for locking the camera into the required position. It's ideal for all types of handheld cameras up to 1.5kg. The mounting kit enables you use a superclamp instead of the suction pad to attach the camera to a roll-bar, roof rail etc. it attaches to anything between 12 & 55mm. in diameter.

Hague Pro Steadymount

Hague Pro Steadymount 

Hague DSLR Motion Cam Stabilizer

Hague DMC (DM-C, DM/C, DM_C, DM C) DSLR Motion Cam Stabilizer The Hague DSLR Motion Cam is a handheld camera stabilizing system that has been specifically designed for DSLR cameras such as the Canon 5D and similar. These stills cameras have become extremely popular as alternatives to camcorders due to the high quality HD Movie Mode, but unfortunately they are difficult to hold, especially when you require moving camera shots. With the DSLR Motion Cam you can create super smooth "Steadicam type" shots. The new Hague DMC DSLR Motion Cam Stabilizer has been designed to cope with different lenses being used, and the fact that on these camera's the tripod mounting hole is never in the centre of balance, which can make them difficult to balance on some stabilizers. On the new DSLR Motion Cam we have increased the range of movement forward & back ,plus extra sideways movement for balance correction. The crucial part of any stabilizer is the gimble, as it is essential that the handle is totally free moving. The Hague DSLR Motion Cam's gimble has a highly polished ball with a nylon socket, plus a radial ball bearing handle ensuring super free movement. This makes it far superior and more effective than any other "ball type" stabilizer on the market. The stabilizer is supplied with a selection of counterbalance weights to support cameras up to 2kg. Once balanced, forward & back fine trim is achieved by manually moving the camera plate forward or back, and sideways fine trim achieved by hinging the weights on the counterbalance plate from side to side. NOT SUITABLE FOR CAMERAS WEIGHING LESS THAN 1kg.

Hague D7 Extra Track - 2 x 2 Meters

Hague D7T (D7-T, D7/T, D7_T, D7 T) D7 Extra Track - 2 x 2 Meters Extra track for Hague D7 Tracker. Set of two 2m lengths.

Hague Tracker

D7 - Hague Tracker The Hague D7 Tracker is quick and easy to set up, has a telescopic column, swivel seat and comes with a 6 metre run of track. This sit on tracking dolly provides smooth tracking shots. The Hague D7 Tracker is a ride on tracking system that is quick and simple to set up and it enables you to create super smooth tracking shots on location or in the studio. An aluminium frame forms the base of the ride on tracking dolly and attached to this is a telescopic column with a 100mm bowl onto which you can fasten your video head. The Hague range of Jibs can also be attached to this column. At the base of the column is a swivel seat, which allows you to move around the column when panning. The width of the dolly has been set to allow it to go through doorways. It runs on 50mm diameter track which is held in position by the 8 radial ball bearing wheels which make the dolly easy to move along the track using the handle supplied. A unique levelling system prevents any rocking should the track be laid on uneven ground.  

Hague Tripod Tracking Dolly (Inc Track)

D5T - Hague Tripod Tracking Dolly Kit The Hague D5T Tripod Tracking Dolly has two sets of locating holes for the tripod legs, which means the tripod can be used in both high and low positions. It has eight radial ball bearing wheels which set the track width to the correct positions as the dolly moves down the track. The Tracking Dolly is ideal for use on location or in the studio, all you need is a reasonably flat surface. The dollies width has been set to allow it to go through doorways, it has its own levelling system which prevents any rocking should the track be on uneven ground. It runs on inexpensive 40mm dia. PVC pipe which can be supplied or is available from DIY stores. The dolly will accept all tripods that have feet smaller than 45mm in diameter or with a base spreader, 3 straps are supplied for securing your tripod to the dolly and also supplied are 2 track connectors for joining your track.

Hague D4 Tripod Dolly

D4 - Hague Tripod Dolly

Hague JIB/Crane Dolly

D3 - Hague Jib & Crane Dolly

Hague Pro Dolly

D2 - Hague Pro Dolly  

Hague Padded Transit Bag

Hague CT46 (CT-46, CT/46, CT_46, CT 46) Padded Transit Bag Suitable for Hague Jibs, Cranes, Booms K8, K9, K10, K12 & D3 Jib & Crane Dolly. The rigid padded transit bag has a heavy-duty zip that runs along three sides of the bag, this enables the top of the bag to be lifted for easy access. Inside the bag is a unique pull-over protective fabric insert to securely wrap equipment within the case. There are internal tie-down straps to make sure equipment stays in place, end handles for easy carrying, and a transport ID tag.  

Hague Multi Jib

Hague Multi Jib 

Hague Camcrane With Stand & Powerhead

Hague Camcrane With Stand & Remote Control Power Head 

Hague Camcrane With Stand & Camera Tilt Control

Hague K9 (K-9, k9, K/9, K_9) Camcrane With Stand & Camera Tilt Control The Hague K9 Camera Crane is one of the longest jibs in the Hague range and comes supplied with its own tripod stand. Utilising the built in pulley system to tilt the camera this boom arm will reach over 5m high allowing you to achieve some spectacular shots as can be seen in the video below. Suitable for cinema cameras, DSLRs and video cameras under 2.5kg in weight, this jib is a very high quality, yet affordable, camera crane for people trying to get a wide range of movement at an affordable price.  The new Hague K9 Camcrane provides smooth movement from ground level to over 5m in height and is ideal for camera set-ups that weigh up to 2.5kg. This makes it a great camera jib for a variety of cinema cameras, camcorders and DSLR cameras. The Hague K9 camera jib is quick and easy to set up and can be used at two different lengths. It is supplied with its own adjustable height jib stand and we also offer a tripod bearing block, as an optional extra, for anyone wanting to utilise their own tripod as a base instead. The K9 camera crane will pan a full 360 degrees on the stand and offers a variable tilt control facility which allows you to tilt the camera up and down when it is attached to the crane. The camera fastens directly to the new camera plate which has been redesigned to offer greater adjustment for DSLR and cinema cameras. The pulley systems then creates the tilt adjustment, or it can be locked off to keep the camera level as the crane is raised or lowered. The camera pulley can also be locked off to any position, so you can have the camera pointing directly up or down, which creates some unusual shots. The jib can be set up at two different lengths with the full length reaching over 5m in height whereas the shorter length keeps it more compact and provides a vertical crane movement of 3.45m. At the shorter length the support cable is not required, and two pulley tilt cables are provided, one for each length.  The counterbalance arm has an adjustable fine trim weight and a weight bar with handgrips. Standard bar weights are used for counterbalance (not supplied). An optional monitor bracket is available, this enables a monitor or a tablet to be fastened to the crane, making it easier to monitor your shots. The K9 Camcrane is made from lightweight aluminium and breaks down into five sections, making it easy to handle in transit. It is supplied in a cardboard carton and a padded transit case is also available as an optional extra.

Hague K2WS Junior Jib with Stand

Hague K2WS Junior Jib With Stand  

Hague Junior Jib

Hague Junior Jib