Call: +44(0) 208 397 1407
Fax: +44(0) 208 307 5055
Free Delivery On Orders Over £150
Read Our Blog For Industry News & Tips
Sell Your Gear Find Out More ›

DPA Surround Kit with 5 x 4006A Clips Windscreens in Peli Case

code: 5006A
  • £5,583.00
  • RRP: £6,345.00
Item Available | Usually dispatched within 24 hours
Free Delivery On Orders Over £150

DPA 5006A (5006 A 5006-A 5006/A) Surround Kit with 5 x 4006A, Clips, Windscreens in Peli Case


  • Five carefully matched microphones
  • Perfect for Decca Tree + rear omnis surround array
  • Specially useful for acoustically accurate reproductions
  • PeliTM Case transportation and protection

The DPA 5006A is a complete DPA 4006A Surround Kit with five carefully factory-matched omni microphones. Even though the standard tolerances on DPA Reference Standards are extremely low, the surround match is even closer.

The specially selected DPA 4006A microphones are matched within ±0.5 dB on both frequency response and sensitivity from mean of set. The maximum phase response difference is 5°.

The natural sound, high sensitivity, low noise-floor and extremely linear frequency response from 10 Hz to 20 kHz (±2 dB) of the microphones make the DPA 4006As the perfect choice for all AB Stereo, Decca Tree or surround main array recordings. The precise reproduction, total transparency and natural-sounding clarity of a DPA 4006A microphone will provide you with a lifetime of satisfying listening.

The foam design in the heavy-duty transportation box allows for fast and easy exchange of microphone/accessory.

Included in this kit:
Carefully matched microphones, sturdy PeliTM case, holders, grids, and windscreens.

Specifications for d:dicate™ 5006A Surround Kit with 4006A Omnis

Directional pattern: Omnidirectional
Principle of operation: Pressure
Cartridge type: Pre-polarized condenser
Frequency range: 10 Hz - 20 kHz
Frequency range, ± 2 dB: 10 Hz - 20 kHz
Sensitivity, nominal, ± 2 dB at 250 Hz: 40 mV/Pa; -28 dB re. 1 V/Pa
Equivalent noise level, A-weighted: Typ. 15 dB(A) re. 20 µPa (maks. 17 dB(A))
Equivalent noise level, ITU-R BS.468-4: Typ. 27 dB (max. 29 dB)
S/N ratio (A-weighted), re. 1 kHz at 1 Pa (94 dB SPL): Typ. 79 dB(A)
Total Harmonic Distortion (THD): < 1 % up to 139 dB SPL peak
Dynamic range: Typ. 124 dB
Max. SPL, peak before clipping: 147 dB
Switchable attenuator: 0 dB / -20 dB
Output impedance: < 200 ohm
Minimum load impedance: 2 kohm
Cable drive capability: 100 m (328 ft)
Output balance principle: Impedance balancing with Active Drive
Common Mode Rejection Ratio (CMRR): > 60 dB
Power supply (for full specifications): 48 V Phantom power (± 4 V)
Current consumption: 2.8 mA
Connector: XLR-3M. Pin 1: shield, Pin 2: signal + phase, Pin 3: - phase
Color: Matte black
Weight: 163 g (5.7 oz)
Microphone diameter: 16 - 19 mm (0.6 - 0.75 in)
Capsule diameter: 16 mm (0.6 in)
Microphone length: 170 mm (6.7 in)
Output voltage, RMS: > 5 V
Polarity: +V at pin 2 for positive sound pressure
Temperature range: -40 °C to 50 °C (-40 °F to 122 °F)
Relative Humidity (RH): Up to 90%
Matching tolerance (freqency response, sensitivity): ± 0.5 dB
Phase deviation for kit: < 5°


Be the first to review DPA Surround Kit with 5 x 4006A Clips Windscreens in Peli Case. Write a review ›
Build Your Own Bundle