Cobalt 9904-UDX-4K-DSP, Like new

Cobalt 9904-UDX-4K-DSP, Like new(FMP60879LPBR)

Good condition, 3 months warranty 

Note - "Five Units Available".

The Cobalt® 9904-UDX-4K-DSP 12G/6G/3G/HD/SD UHD Up/Down/Cross Converter/Frame Sync with DSP Advanced Audio Processing is Cobalt’s next generation of advanced scaler/frame synchronizers for the openGear® platform. 

The 9904-UDX-4K-DSP upconverts 12G/6G/3G/HD/SD to either UHD1 3840x2160 Square DIvision Multiplex (SDM) or Two-Sample Interleave (2SI) quad 3G-SDI based formats, or can output ST 2082 12G-SDI for single-wire 4K transport. With both 12G-SDI and quad 3G-SDI inputs, the 9904-UDX-4K can downconvert 12G and quad UHD. The 9904-UDX-4K provides an HDMI 2.0 output for economical 4K video monitoring. The 9904-UDX-4K-DSP offers numerous options, including SDR-to-HDR conversion and color correction.

The 9904-UDX-4K-DSP offers a DSP-based platform that supports multiple advanced audio DSP options, including Dolby® Real-Time Loudness Leveling automatic loudness processing, Dolby® E/D/D+ encode/decode, and Linear Acoustic® UPMAX™ automatic upmixing. Embedded audio and metadata are properly delayed and re-embedded to match any video processing delay, with full adjustment available for audio/video offset.

The high-density openGear® design allows for up to five 9904-UDX-4K-DSP cards to be installed in one 2RU openGear® frame. Card control/monitoring is available via DashBoard user interface or Cobalt’s RESTful-based Reflex protocol.

12G/6G/3G/HD/SD-SDI Input/Outputs

(6) 75Ω inputs (max)

(8) 75Ω outputs (max)

SDI Formats Supported: SMPTE ST2082-1,10, 424M, 292M, SMPTE 259M-C. All inputs/outputs 12G compliant and SDQS/2SI quad 3G compliant.

Return Loss:

> 15 dB up to 1.485 GHz

> 10 dB up to 3 GHz

> 7 dB up to 6 GHz

> 5 dB up to 12 GHz

Input Cable Length:

45m Belden 1694A cable at 11.88 Gbps

120m Belden 1694A cable at 2.97 Gbps

240m Belden 1694A cable at 1.485 Gbps

400m Belden 1694A cable at 270 Mbps

Output Signal Level: 800 mV ±10%

DC Offset: 0 V ± 50 mV

Rise and Fall Time @ 11.88 Gbps: < 45 ps

Alignment Jitter (12G/3G/HD/SD): < 0.3/0.3/0.2/0.2 UI

Frame Sync Audio/VIdeo Delay

Max offset: 20 frames

Latency (min): 1 frame

User Audio Delay Offset from Video

Bulk delay control: -33 msec to +3000 msec.

Per-channel delay controls: -800 msec to +800 msec

AES Audio Inputs/Outputs

(8) AES-3id 75Ω coaxial ports; port direction assignable as inputs or outputs in groups of 4 ports.

Note: Hardware rev –E and later has 8 AES ports; earlier versions have 4 port max.

MADI Audio Inputs/Outputs

(2) 75Ω coaxial ports (max)

Note: Not all rear modules support full MADI I/O. MADI I/O is a function of Rear Module used

and is available only on card with on rev C (or later) hardware with firmware supporting MADI I/O.

See Rear Module illustrations for specific information.

HDMI Input (Option -H2S only)

HDMI 2.0 Input; mini connector

HDMI Output

HDMI 2.0 Output; type A standard connector

GPIO

6 GPI (max); 2 GPO (max)

Note: GPIO max capacity is a function of Rear Module used. See Rear Module Options tab for specific information.

Frame Reference Input

(2) reference from frame bus. SMPTE 170M/318M “Black Burst”, SMPTE 274M/296M “Tri-Level”

Frame Loading (Max. recommended number of 9904 cards supported per Frame Model)

  •OG3 Frame: (5) cards

  •HPF-9000 Frame: (5) cards

  •HPF-9500 Frame: (5) cards

  •oGx Frame: (7) cards

  •HPF-MAX Frame: (10) cards

Note: Excluding the HPF-MAX, it is recommended to leave a 1RU gap above the frame and set frame Network Controller Card to run the frame cooling fans at full (max.) speed.

In The Box:-

1x Cobalt 9904-UDX-4K-DSP