Sony HXRNX30E 1/2.88-inch full hd camcorder

• Acoustic Principle: Line Gradient
• Active Electronics: JFET impedance convertor with balanced transformer output
• Capsule 0.50"
• Polar Pattern: Supercardioid
• Address Type: End
• Frequency Range: 20Hz - 20kHz
• Output Impedance: 250Ω
• Maximum SPL: 131dBSPL
• Maximum Output Level: 6.9mV (@ 1kHz, 1% THD into 1KΩ load)
• Sensitivity: -36.0dB re 1 Volt/Pascal (15.00mV @ 94 dB SPL) +/- 2 dB @ 1kHz
• Equivalent Noise Level (A-weighted): 18dBA
• Power Options: AA Battery+48V phantom power
• Weight: 161.00g
• Dimensions: 280.00mmH x 22.00mmW x 22.00mmD
• Output: XLR Output

The new RODE NTG-2 is a lightweight condenser shotgun microphone, designed for professional applications within the film, video, television and production industries. 
The NTG-2 provides a balanced low impedance output stage and operates either from an internal 1.5 V battery (AA) or 48 V to the P48 standard. A wide bandwidth and controlled polar response coupled with low noise SMT electronics, makes the NTG-2 the perfect choice for film, video engineering and voice-over work. The NTG-2 is extremely lightweight making it ideal for mounting directly to video cameras or on boom poles. 
The NTG-2 comes complete with mount and windshield.The windscreen effectively suppresses wind noise when recording outdoors in moderate conditions.

Included accessories: ZP2 (zip pouch), RM5 (stand mount) WSVM (windshield)

The RØDE WS6 Deluxe Windshield is designed to reduce wind noise when recording in adverse environmental conditions.

Suitable for the RØDE NTG-1 and NTG-2, as well as any shotgun microphone with a maximum slot length of 160.5mm (6 1/4") and a diameter of 21-22.5mm.

Acoustic Principle Line Gradient

Active Electronics JFET impedance convertor with balanced transformer output

Capsule 0.50"

Polar Pattern Supercardioid

Address Type End

Frequency Range 20Hz - 20kHz

Output Impedance 250Ω

Maximum SPL 131dB SPL (@ 1kHz, 1% THD into 1KΩ load)

Maximum Output Level 6.9mV

Sensitivity -36.0dB re 1 Volt/Pascal (15.00mV @ 94 dB SPL) +/- 2 dB @ 1kHz

Equivalent Noise Level (A-weighted) 18dB-A

Power Options AA Battery+48V phantom power

Weight 161.00gm

Dimensions 280.00mmH x 22.00mmW x 22.00mmD

Output XLR Output

Acoustic Principle Line Gradient

Active Electronics JFET impedance convertor with balanced transformer output

Capsule 0.50"

Polar Pattern Supercardioid

Address Type End

Frequency Range 20Hz - 20kHz

Output Impedance 250Ω

Maximum SPL 131dB SPL (@ 1kHz, 1% THD into 1KΩ load)

Maximum Output Level 6.9mV

Sensitivity -36.0dB re 1 Volt/Pascal (15.00mV @ 94 dB SPL) +/- 2 dB @ 1kHz

Equivalent Noise Level (A-weighted) 18dB-A

Power Options AA Battery+48V phantom power

Weight 161.00gm

Dimensions 280.00mmH x 22.00mmW x 22.00mmD

Output XLR Output

The new RODE NTG-2 is a lightweight condenser shotgun microphone, designed for professional applications within the film, video, television and production industries. 
The NTG-2 provides a balanced low impedance output stage and operates either from an internal 1.5 V battery (AA) or 48 V to the P48 standard. A wide bandwidth and controlled polar response coupled with low noise SMT electronics, makes the NTG-2 the perfect choice for film, video engineering and voice-over work. The NTG-2 is extremely lightweight making it ideal for mounting directly to video cameras or on boom poles. 
The NTG-2 comes complete with mount and windshield.The windscreen effectively suppresses wind noise when recording outdoors in moderate conditions.

Included accessories: ZP2 (zip pouch), RM5 (stand mount) WSVM (windshield)

RØDE Microphones releases the Blimp, an all new suspension windshield for use with professional shotgun microphones.

The new RØDE Blimp is a complete windshield and shock mounting accessory, designed to accommodate the RØDE NTG-1, NTG-2 and NTG-3 shotgun microphones in addition to the NT4 stereo microphone and most third party shotgun microphones up to 325mm (12 ¾â€) in length.

“During the design of the RØDE Blimp we continually focussed on adding tangible performance benefits for the user.” explained the RØDE Blimp’s Lead Industrial Designer, Matthew Hall. “None of the features unique to the Blimp were incorporated without careful analysis and consideration for their purpose. We took great care to ensure all elements worked cohesively and were integrated into the overall design in a manner to provide the best possible windshield product on the market today.”

The Blimp’s main housing is based on a 10 frequency geodesic dome, with a triangular cross-section that allows the part to be injection-moulded in one piece. This geometry creates a high open-area ratio that greatly improves the acoustic transparency over existing solutions, yet an unparalleled level of robustness and physical protection for the microphone. The end-domes can be easily removed by twisting off, allowing easy access to the microphone. An oversize thread allows easy and intuitive re-attachment of the domes, avoiding clip systems that are difficult to use and vulnerable to breaking.

A high quality ‘Dead Wombat’ synthetic fur cover and brush is supplied for additional wind protection in extreme environments.

5 Meter 3 Pin XLR Cable

The new RODE NTG-2 is a lightweight condenser shotgun microphone, designed for professional applications within the film, video, television and production industries. 
The NTG-2 provides a balanced low impedance output stage and operates either from an internal 1.5 V battery (AA) or 48 V to the P48 standard. A wide bandwidth and controlled polar response coupled with low noise SMT electronics, makes the NTG-2 the perfect choice for film, video engineering and voice-over work. The NTG-2 is extremely lightweight making it ideal for mounting directly to video cameras or on boom poles. 
The NTG-2 comes complete with mount and windshield.The windscreen effectively suppresses wind noise when recording outdoors in moderate conditions.

Included accessories: ZP2 (zip pouch), RM5 (stand mount) WSVM (windshield)

RØDE Microphones releases the Blimp, an all new suspension windshield for use with professional shotgun microphones.

The new RØDE Blimp is a complete windshield and shock mounting accessory, designed to accommodate the RØDE NTG-1, NTG-2 and NTG-3 shotgun microphones in addition to the NT4 stereo microphone and most third party shotgun microphones up to 325mm (12 ¾â€) in length.

“During the design of the RØDE Blimp we continually focussed on adding tangible performance benefits for the user.” explained the RØDE Blimp’s Lead Industrial Designer, Matthew Hall. “None of the features unique to the Blimp were incorporated without careful analysis and consideration for their purpose. We took great care to ensure all elements worked cohesively and were integrated into the overall design in a manner to provide the best possible windshield product on the market today.”

The Blimp’s main housing is based on a 10 frequency geodesic dome, with a triangular cross-section that allows the part to be injection-moulded in one piece. This geometry creates a high open-area ratio that greatly improves the acoustic transparency over existing solutions, yet an unparalleled level of robustness and physical protection for the microphone. The end-domes can be easily removed by twisting off, allowing easy access to the microphone. An oversize thread allows easy and intuitive re-attachment of the domes, avoiding clip systems that are difficult to use and vulnerable to breaking.

A high quality ‘Dead Wombat’ synthetic fur cover and brush is supplied for additional wind protection in extreme environments.

Telescopic Boom Pole. Extends to 3m. Suits Videomic, NTG1 / NTG2.

Suspension shock mount (cold shoe adaptor). 
Made for the RØDE NTG series. Features a 4-way rubber suspension system with quick release tilt mechanism, and a 3-way mounting system with 1/4"x20 and 3/8"x16 internal threads for boom pole or tripod mounting and a standard hot shoe adaptor for direct camera mounting. Will work with all similar diameter shotgun mics.

5 Meter 3 Pin XLR Cable

The NTG-3 is the result of years of development by RØDE engineers, providing the professional broadcast and film industries with an affordable yet uncompromising microphone.

Using a technology known as RF-bias the RØDE NTG-3 is almost completely resistant to moisture, making it the only option when recording in any demanding environments where condensation is an issue.

In addition to its robust properties the NTG-3 combines very low weight (163g), a durable anti-glare finish and incredibly low handling and self-noise (13dBA) to become RØDE’s premier A/V microphone.

When not in use the NTG-3 can be stored away in the included weather resistant aluminium storage cylinder, providing additional protection when travelling and storing the microphone.

• Designed to withstand adverse environmental conditions
• 50% less self-noise than the majority of shotgun microphones
• True condenser (externally RF biased)
• Extremely low handling noise
• High level of immunity to radio frequency broadcast
• Superior broadcast sound quality
• Weather resistant aluminium storage cylinder

The RØDE WS7 Large Deluxe Windshield is designed to reduce wind noise when recording in adverse environmental conditions.

Suitable for the RØDE NTG-3 and any shotgun microphone with a maximum slot length of 186.5mm (7 1/4") and a diameter of 19-20mm.

12inch 3Pin Xlr Cable

The NTG-3 is the result of years of development by RØDE engineers, providing the professional broadcast and film industries with an affordable yet uncompromising microphone.

Using a technology known as RF-bias the RØDE NTG-3 is almost completely resistant to moisture, making it the only option when recording in any demanding environments where condensation is an issue.

In addition to its robust properties the NTG-3 combines very low weight (163g), a durable anti-glare finish and incredibly low handling and self-noise (13dBA) to become RØDE’s premier A/V microphone.

When not in use the NTG-3 can be stored away in the included weather resistant aluminium storage cylinder, providing additional protection when travelling and storing the microphone.

• Designed to withstand adverse environmental conditions
• 50% less self-noise than the majority of shotgun microphones
• True condenser (externally RF biased)
• Extremely low handling noise
• High level of immunity to radio frequency broadcast
• Superior broadcast sound quality
• Weather resistant aluminium storage cylinder

The RØDE WS7 Large Deluxe Windshield is designed to reduce wind noise when recording in adverse environmental conditions.

Suitable for the RØDE NTG-3 and any shotgun microphone with a maximum slot length of 186.5mm (7 1/4") and a diameter of 19-20mm.

Telescopic Boom Pole. Extends to 3m

5 Meter 3 Pin XLR Cable

NTSM3

Suspension shock mount (cold shoe adaptor). 
Made for the RØDE NTG series. Features a 4-way rubber suspension system with quick release tilt mechanism, and a 3-way mounting system with 1/4"x20 and 3/8"x16 internal threads for boom pole or tripod mounting and a standard hot shoe adaptor for direct camera mounting. Will work with all similar diameter shotgun mics.

The NTG-3 is the result of years of development by RØDE engineers, providing the professional broadcast and film industries with an affordable yet uncompromising microphone.

Using a technology known as RF-bias the RØDE NTG-3 is almost completely resistant to moisture, making it the only option when recording in any demanding environments where condensation is an issue.

In addition to its robust properties the NTG-3 combines very low weight (163g), a durable anti-glare finish and incredibly low handling and self-noise (13dBA) to become RØDE’s premier A/V microphone.

When not in use the NTG-3 can be stored away in the included weather resistant aluminium storage cylinder, providing additional protection when travelling and storing the microphone.

• Designed to withstand adverse environmental conditions
• 50% less self-noise than the majority of shotgun microphones
• True condenser (externally RF biased)
• Extremely low handling noise
• High level of immunity to radio frequency broadcast
• Superior broadcast sound quality
• Weather resistant aluminium storage cylinder

RØDE Microphones releases the Blimp, an all new suspension windshield for use with professional shotgun microphones.

The new RØDE Blimp is a complete windshield and shock mounting accessory, designed to accommodate the RØDE NTG-1, NTG-2 and NTG-3 shotgun microphones in addition to the NT4 stereo microphone and most third party shotgun microphones up to 325mm (12 ¾â€) in length.

“During the design of the RØDE Blimp we continually focussed on adding tangible performance benefits for the user.” explained the RØDE Blimp’s Lead Industrial Designer, Matthew Hall. “None of the features unique to the Blimp were incorporated without careful analysis and consideration for their purpose. We took great care to ensure all elements worked cohesively and were integrated into the overall design in a manner to provide the best possible windshield product on the market today.”

The Blimp’s main housing is based on a 10 frequency geodesic dome, with a triangular cross-section that allows the part to be injection-moulded in one piece. This geometry creates a high open-area ratio that greatly improves the acoustic transparency over existing solutions, yet an unparalleled level of robustness and physical protection for the microphone. The end-domes can be easily removed by twisting off, allowing easy access to the microphone. An oversize thread allows easy and intuitive re-attachment of the domes, avoiding clip systems that are difficult to use and vulnerable to breaking.

A high quality ‘Dead Wombat’ synthetic fur cover and brush is supplied for additional wind protection in extreme environments.

12inch 3Pin Xlr Cable

Transducer Condenser

Polar Pattern Line-gradient supercardioid

Frequency Response 40 Hz to 20 kHz

Dynamic Range (Typical) 117 dB

Signal-to-Noise Ratio 81 dB SPL (A-weighted)

Maximum Input Sound Level 130 dB

Power Requirements 48V Phantom power

Nominal Impedance 25Ω

Output Connectors 3-pin XLR

Pad No

Low Frequency Roll-Off No

Dimensions (L x Diam) 10 x 0.74" (255 x 19 mm)

Weight 5.74 oz (163 g)